Panasonic WH-MXF09D3E8 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 125

background image

73

16.3 Breakdown Self Diagnosis Function

16.3.1 Self Diagnosis Function (Three Digits Alphanumeric Code)

When abnormality occur during operation, the system will stop operation, and OFF/ON remote control LED will

blink and error code will display on the remote control Timer display LCD.

Even error code is reset by turning OFF power supply or by pressing ERROR RESET button, if the system

abnormality is still un-repaired, system will again stop operation, and OFF/ON remote control LED will again blink.

The error code will store in IC memory.

To check the error code

1.  When an abnormality occurs, system will stop operation and OFF/ON remote control LED will blink.
2.  Error code of the abnormality will display on the remote control Timer display LCD.
3.  To determine the abnormality description, the Error Code Table needs to be referred.

To display past/last error code

1.  Turn ON power supply.
2.  Press and hold the CHECK button for more than 5 seconds to enter status mode.
3.  Press the SEARCH DOWN/UP button to retrieve past/last error code.
4.  Press the CANCEL button or wait 30 seconds to exit status mode.

To permanently delete error code from IC memory

1. Turn ON power supply.
2. Press and hold the ERROR RESET button for more than 8 seconds till a beep sound is heard.

«
...
71
72
73
74
75
...
»

Содержание WH-MXF09D3E8






























































































































Отзывы:

Нет отзывов

Похожие инструкции для WH-MXF09D3E8

Бренд: Harry Taylor Страницы: 56

Бренд: Harry Taylor Страницы: 52

Бренд: Lasko Страницы: 4

Бренд: Wacker Neuson Страницы: 38

Бренд: Samsung Страницы: 27

Бренд: iBath Страницы: 12

Бренд: DAYLIFF Страницы: 12

Бренд: Gamo Страницы: 25

Бренд: Gamma Vacuum Страницы: 27

Бренд: YAMADA Страницы: 14

American Pride ACNF Series

Бренд: Amana Страницы: 8

Бренд: Prem-I-Air Страницы: 7

Бренд: Liberty Pumps Страницы: 16

Bell & Gossett Domestic 616PF

Бренд: Xylem Страницы: 4

Бренд: Euromatic Страницы: 16

Бренд: N'oveen Страницы: 21

Бренд: EBARA Страницы: 28

NEXIS-VE Series

Бренд: salmson Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды