Panasonic WH-MXF09D3E8 Скачать руководство пользователя страница 42

Страница: 42 / 125

B. If Remote Control Cable Is Exposed

1 Install the remote control lower case to the

wall with the two accessory screws (4).

2 Fasten the screws properly until screw head is

lower than the rib and reach the base of
remote control lower case to ensure they do
not damage the PCB inside the remote control
(1).

3 The feeding-out direction for the remote

control cable can be either via top, left or right
side.

4 Use nipper to cut a notch at the upper case.

(Select the intended feeding-out position)

5 Route the remote control cable (2) inside the

lower case in accordance with the intended
feeding-out direction. (Refer to the illustration
at below)

6 Insert firmly the connector of remote control

cable (2) to connector (CON1) in the upper
case circuit board. (Refer to the illustration at
below)

7 Secure the remote control upper case to the

lower case with the tabs provided.

11.4.3.3 Connecting The Remote Control Cable To Mono bloc Unit

WARNING

Be sure to turn off the main power before installing and
connecting the remote control. Otherwise, it will cause the
electrical shock.

1 Remove the cabinet front plate.
2 Connect the remote control cable with the

provided connector as shown in below
illustration. (Refer wiring diagram for detail.)

3 Guide the remote control cable through the

clamper and Bushing

(Refer illustration “How to connect Remote
Control to Provided Connector” for detail.)

4 Reinstall the cabinet front plate after

connection complete.

Содержание WH-MXF09D3E8






























































































































Результаты поиска

Содержание WH-MXF09D3E8

Отзывы:

Похожие инструкции для WH-MXF09D3E8

Бренды по названию

Популярные бренды

Panasonic WH-MXF09D3E8, Руководство по обслуживанию

Результаты поиска

Содержание WH-MXF09D3E8

Отзывы:

Похожие инструкции для WH-MXF09D3E8

Бренды по названию

Популярные бренды