Panasonic WH-MDF09C3E8 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 129

background image

59

12.3 Pump Down Operation

Purpose

Ensure the pump down operation when relocating or disposing of the unit. The pump down operation will extract all
refrigerant from the piping into the mono bloc unit.

Pump down operation control:

1  Press the SERVICE S/W for continuous 5 secs to enter Service mode.
2  In service mode, select Sr:01 and press SET S/W to start Pump Down operation.
3  There will be no Low Pressure error & Freeze prevention judgement during pumpdown operation.
4  3 ways valve will shift to room side.
5  Press the ON/OFF button to stop the unit.

12.4 Flow

Switch

12.4.1 Flow Switch Control

1 The water flow switch serve as an overload protector that shuts down the unit when the water level is

detected to be low.

2 Detection is Lo (0V) when there is no water flow, and detection is Hi (5V) when there is water flow.

12.5 Force Heater Mode Operation

The backup heater also serves as backup in case of malfunctioning of the mono bloc unit.

1  Make sure the OFF/ON remote control LED is OFF (no operation).
2  Press the Force button to start the force heater mode operation.
3  During force heater mode, all other operations are not allowed.
4  Press OFF/ON button to stop the force heater mode operation.

«
...
57
58
59
60
61
...
»

Содержание WH-MDF09C3E8


































































































































Отзывы:

Нет отзывов

Похожие инструкции для WH-MDF09C3E8

Бренд: TradeQuip Страницы: 8

Бренд: Graco Страницы: 48

Бренд: Carrier Страницы: 12

Бренд: veito Страницы: 24

Бренд: Vasco Страницы: 32

Бренд: Galletti Страницы: 60

Бренд: Unitary products group Страницы: 16

Inverter Design

Бренд: Thermia Страницы: 16

Бренд: Dimplex Страницы: 64

Бренд: Radiatori 2000 Страницы: 20

Бренд: Masterflex Страницы: 28

Gusher 30 Series

Бренд: Whale Страницы: 8

Бренд: Yoshitake Страницы: 6

Бренд: RainPoint Страницы: 32

Бренд: Becker Страницы: 6

CENTRI PUPPY 18510-000 Series

Бренд: JABSCO Страницы: 4

Бренд: Dru Страницы: 56

Бренд: Zoeller Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды