Panasonic U-4LE1R8 Скачать руководство пользователя страница 82

Страница: 82 / 119

Mini VRF SYSTEM

Trouble Diagnosis

3-42

3. Mini VRF System Alarm Codes

1-1

1-2

Check for
open circuit and
the voltage at the
breaker. if a problem
is found, fix it and
check again.

Yes

Turn the power back on and check again. Is the alarm triggered
again?

1-2

2-1

3-1

Yes

1 Check

the power
supply &
the wiring

Are the wires (RE1, RE2) from the reactor firmly installed?

2-1

2-2

Correct wiring

Yes

Turn the power back on and check again. Is the alarm triggered
again?

4hp, 5hp:

Common in RE1 and RE2

Plug-in type

6hp: Fastening screw type

2-2

Replace the outdoor
unit HIC PC board.

3-1

Yes

2 Check the

outdoor
unit CR
board

There may be a Instantaneous blackout failure.
If there is nothing abnormal, see what happens.

RE1

RE2*

3-1

3 Final check

P05 Power Supply Error

Error Detection Method

Error Diagnosis

Instantaneous blackout

•

Note : The work involved in diagnosing each of the items is extremely dangerous, so turn the power off at the breaker before

performing the tests.

Zero-cross (waveform input of power supply) error

•

DC voltage charge failure

•

Is the voltage on each of the terminal boards 10% of the
rated voltage?

RE1

RE2

Sigle-phase outdoor unit HIC board

3-phase outdoor unit HIC board

SM830209-00̲Mini̲VRF SYS.indb 42

2012/01/11 18:25:33

Содержание U-4LE1R8
























































































































Результаты поиска

Содержание U-4LE1R8

Отзывы:

Бренды по названию

Популярные бренды

Panasonic U-4LE1R8, Руководство по обслуживанию

Результаты поиска

Содержание U-4LE1R8

Отзывы:

Бренды по названию

Популярные бренды