Panasonic SG-P Series Скачать руководство пользователя страница 57

Страница: 57 / 76

Symptom

Indicator

Number
of
blinkings

Cause

Solution

Referen
ce page

The OSSD wiring is short
circuited. (Standard unit
only)

Correctly wire the OSSD1
(black) and OSSD2 (white) lines
according to the wiring diagram.

"P.3-8"

The OSSD wiring is not
correct. (Standard unit only)

Correctly wire the OSSD1
(black) and OSSD2 (white) lines
according to the wiring diagram.

"P.3-8"

The check input / check
output wiring is short
circuited or disconnected.
(Standard unit only)

Correctly wire the check input
(pink) and check output (gray)
lines according to the wiring
diagram.

"P.3-8"

The check input / check
output wiring is not correct.
(Standard unit only)

Correctly wire the check input
(pink) and check output (gray)
lines according to the wiring
diagram.

"P.3-8"

The power supply voltage
supplied to this device is
beyond the usage range.

Use the power supply unit with
the supply voltage of 24 VDC
+10%/ -20%.

"P.

7-2"

Affected by the noise.

Check the noise environment
around this device.
Check the wiring and the
voltage and capacity of the
power supply.
If the device does not operate
properly even after checking,
please contact our office.

The
indicator
does not
light at all.

Turns

OFF

The power wiring is short
circuited or disconnected.

Correctly wire the check +V
(brown) and 0V (blue) lines
according to the wiring diagram.

"P.3-8"

Power is not supplied.

Check if the capacity of the
power supply is sufficient.
Correctly connect the power
supply unit.

"P.

7-2"

The power supply voltage is
not within the specifications.

Use the power supply unit with
the supply voltage of 24 VDC
+10%/ -20%.

"P.

7-2"

Switch body is faulty.

Replace the switch body.

The OSSD
does not
turn OFF.

The distance between the
switch body and the
actuator is longer than the
specified operating distance
Sar (ON→OFF).

Make sure that the distance
between the switch body and
the actuator within the
specification range.

"P.

7-2"

The OSSD
repeatedly
turns ON
and OFF at
high speed.

The pulse signal (OFF) that
is periodically generated by
the OSSD is recognized by
a connected device.

Connect a device that does not
detect the periodical pulse
signal (OFF).

The switch
body does
not detect
the actuator.

An actuator manufactured
by other company is used.

Use an

SG-P

Series actuator.

6.1 Troubleshooting

WUME-SGPUM-2

6-3

Содержание SG-P Series













































































Результаты поиска

Содержание SG-P Series

Отзывы:

Похожие инструкции для SG-P Series

Бренды по названию

Популярные бренды

Panasonic SG-P Series, Инструкция по эксплуатации

Результаты поиска

Содержание SG-P Series

Отзывы:

Похожие инструкции для SG-P Series

Бренды по названию

Популярные бренды