GB6
GB7
Control Panel and Display
n
Operation status
Displayed for the current stage of the program except
and
.
: Provide an indication of a power failure.
:
●
Provide an indication of adding ingredients manually.
(Menu 2, 3, 5, 7, 10, 11 and 12.)
●
Provide an indication of doing manual operation. (Menu 12 and 15.)
n
Time showing
●
Time remaining until ready.
●
When adding ingredients manually, display
will show the time until adding extra
ingredients in the program.
●
Menu required some manual steps, display
will show the remaining time until starting its
process after press
Start
button.
n
Menu
●
Press this button once to be a setting mode.
●
Press this button again to change Menu number.
(To advance more quickly, hold the button.)
See P. GB10 for menu number.
n
Status indicator
●
Flash indicates that the machine is in set state or manual
operation is required.
Start
button can be pressed.
●
Always light indicates that the machine is in program
execution state.
Start
button cannot be pressed.
It will not turn on even plugged in.
n
Size
Press this button to choose
size. See P. GB10 for
available menu.
L
M
n
Crust
Press this button to choose
crust colour. See P. GB10
for available menu.
Medium
Light
n
Start
Press this button to start
the program.
n
Stop
To cancel the setting / stop the program.
(Hold for approximately 1 second.)
n
Timer
●
Set delay timer (time until bread is ready). For available menu, it can be set up to 13 hours. (See P. GB10)
e.g.: It is 9:00 PM now, and you want the bread to be ready at 6:30 the next morning.
É
Set the timer to
9:30
(9 hours and 30 minutes from now).
12
9
3
12
9
3
6
6
9 h 30 min
from now
Current time
Ready time
●
Setting time for menu 13 and 18:
•
Menu 13
Press the button once will advance the baking time including additional baking time by 1 minute.
•
Menu 18
Press the button once will advance the cooking time by 10 minutes but additional cooking time will be by 1 minute.
●
Picture shows all words and symbols, but only those relevant will be displayed during operation.
Parts Names and Instructions
Bread pan and kneading blade
are coated with ceramic to avoid stains and to make bread easier to remove.
n
To avoid damaging their ceramic coating, please follow the instructions below:
●
Do not use hard or sharp utensils such as a knife or a fork when removing the bread from the bread pan or / and
removing the kneading blade from the bread or bread pan.
•
If bread sticks to bread pan and is difficult to be taken out, leave the bread pan for 5 minutes
– 10 minutes to cool.
Turn the bread pan upside down using oven gloves (see P. GB12). Tap holding both hands onto a clear cooking
surface covered with kitchen towel until the bread comes out.
●
The kneading blade may remain stack in the bread. If still remains, wait for the bread cool down and take it out
before slicing.
•
If the kneading blade cannot be removed from bread pan, pour warm water into the bread pan and wait 5 minutes –
10 minutes.
Still difficult to remove, turn kneading blade laterally and pull it out.
●
Use the soft sponge when cleaning the bread pan and the kneading blade.
Do not use anything abrasive such as cleansers or scouring pads.
●
Hard, coarse or large ingredients such as flours with whole or ground grains, sugar, or the addition of nuts and seeds may damage their
ceramic coating. If using large chunk of ingredient, break or cut into small pieces. Please follow the information of
Additional Ingredients
(see P. GB9) and the recipe quantities stated.
●
Use only supplied kneading blade for this appliance.
The bread pan, kneading blade, and bread may be very hot after baking. Always handle with care.
Steam vent
Measuring cup
Measuring spoon
●
10 mL increments
(Max. 310 mL)
(15 mL)
(5 mL)
Tablespoon
●
½ marking
Teaspoon
●
¼, ½, ¾
markings
Mains plug *
* The shape of mains plug may be different from illustration.
Lid
Handle
Kneading blade
Control panel
Mains lead
Main Unit
Accessories
Main Unit & Accessories
Bread pan
Kneading
mounting shaft
▲
Press this button to increase the time.
▼
Press this button to decrease the time.
(To advance more quickly, press this button once then hold it.)
English
SD-ZP2000 EN_DE_OI5.indd 6-7
16/7/2018 20:00:38
