VQT2R71
27
Error messages/Using with headphones/Speci
fi
cations
Troubleshooting and
other information
Error messages
Speci
fi
cations
Using with headphones
Turn down the volume as closest as to the minimum value.
• Plug type: ø 3.5 mm stereo mini plug
W
(Headphone) jack
Headphones
(not supplied)
Note
• Avoid listening for prolonged periods of time to prevent hearing
damage.
• Multi-channel signals are forcibly converged to 2-channel and
output. (2CH MIX)
However, for DVD audio, the front left and right signals are output.
• Excessive sound pressure from earphones and headphones can
cause hearing loss.
Display
Check point/Cause/Countermeasure
Pages
CANCEL MUTE FUNCTION
(Scrolling)
• The test signal is not output while muting is on.
Cancel muting for operation.
22
MUTE
(Blinking)
• This is always displayed while muting is on.
22
NOT POSSIBLE FOR
THIS INPUT SOURCE
(Scrolling)
• You cannot use Dolby Virtual Speaker, SFC and Dolby Pro Logic for dual
sounds.
—
NOT POSSIBLE FOR
THIS PCM SOURCE
(Scrolling)
• You cannot use Dolby Virtual Speaker, SFC and Dolby Pro Logic effect with
PCM signals with sampling frequency of over 48 kHz.
19
NOT POSSIBLE WHEN USING
HEADPHONES
(Scrolling)
• You cannot use the sound field effects when using headphones.
below
REMOTE 2
REMOTE 1
• Set the same remote control code for this main unit and remote control. When “
REMOTE 2
”
is displayed, set the code to “
2
” on the remote control in step
4
of procedure “When other
equipment (mini component system, AV amp, etc.) manufactured by Panasonic operates
with the remote control operations of this system”. When “
REMOTE 1
” is displayed, set the
code to “
1
” on the remote control in step
4
in the same way.
26
SWITCH OFF POWER
(Scrolling)
• While “
F70
” is displayed, all operations but turning ON/OFF operation are not
available. Turn off the system, unplug the AC mains lead, and consult your dealer.
—
TURN OFF DTS FIX MODE
(Scrolling)
• When each input is fixed to DTS (DTS FIX), the sound field effects cannot be
cancelled even if you press [–SETUP, OFF]. Cancel DTS FIX.
26
U701
• The equipment connected by the HDMI cable is not compatible with this
system’s copyright protection technology.
—
U703
• A problem has occurred with the HDMI connection. Try the following to correct
the problem. Consult your dealer if the error code remains on the display.
– Turn the connected equipment off and on again.
– Disconnect the HDMI cable then reconnect it.
– Do not connect more than 2 sets of equipment to this system’s output.
—
U704
• The system received incompatible video signals through HDMI connection.
Check the settings of the connected equipment.
—
g
PRE AMPLIFIER SECTION
Input sensitivity / Input impedance
TV, AUX3
600 mV / 47 k
Ω
S/N ratio (IHF A)
BD/DVD, TV, AUX1,
AUX2 (Digital Input)
80 dB (IHF ’66)
Tone controls
BASS
50 Hz, + 6 to – 6 dB
TREBLE
20 kHz, + 6 to – 6 dB
Input/Output terminal
AUDIO IN
( TV, AUX3 )
2
DIGITAL AUDIO IN
OPTICAL 1, 2 ( TV, AUX2 )
2
AUDIO OUT
( FRONT L/R, SURROUND L/R )
4
SUBWOOFER OUT
1
HEADPHONE OUT ( 16 to 64
Ω
)
1
AV
HDMI IN ( BD/DVD, AUX1 )
2
HDMI OUT ( TO TV (ARC))
1
This system supports “HDAVI Control 4” function.
g
MAIN UNIT GENERAL
Power supply
For E, GN
AC 220 to 240 V, 50 Hz
For GS
AC 110 to 240 V, 50/60 Hz
Power consumption
16 W
In standby condition
0.5 W
In standby condition ( HDMI off mode )
0.2 W
Dimensions ( W x H x D )
430 mm x 59 mm x 262 mm
Mass
Approx. 2 k
g
Operating temperature range
0 °C to 40 °C
Operating humidity range
20 % to 80 % RH (no condensation)
g
WIRELESS SECTION
Frequency of the using band
2.4000 GHz to 2.4835 GHz
Number of using channels
3
The reaching distance
15 m
∗
1
∗
1 It is under the condition as follows.
At same room indoor, there is not an obstacle
between the main unit and the speaker.
And installing a main unit in the position with
equal to or more than 50 cm height.
SPEAKER
g
POWER AMPLIFIER SECTION
∗
2
RMS output power (at AC 220 to 240 V)
10 % total harmonic distortion
Woofer Speaker ch
60 W (100 Hz, 3
Ω
)
Mid High Speaker ch
20 W (1 kHz, 8
Ω
)
System Total Power
∗
3
160 W (80 W + 80 W)
DIN output power (at AC 220 to 240 V)
1.0 % total harmonic distortion
100 Hz Woofer Speaker ch
40 W (3
Ω
)
1 kHz Mid High Speaker ch
15 W (8
Ω
)
System Total Power
∗
3
110 W (55 W + 55 W)
g
SPEAKER SECTION
∗
2
2 way 5 speakers system (Bass reflex type)
Woofer part
12 cm cone type × 1
Mid High part
2.4 × 10 cm flat type × 4
g
SPEAKER GENERAL
∗
2
Power supply
For E, GN
AC 220 to 240 V, 50 Hz
For GS
AC 110 to 240 V, 50/60 Hz
Power consumption
20 W
Wireless link standby
0.8 W
In standby condition
0.15 W
Dimensions ( W x H x D )
290 mm × 1231 mm × 290 mm
Mass
Approx. 3.9 k
g
Operating temperature range
0 °C to 40 °C
Operating humidity range
20 % to 80 % RH (no condensation)
∗
2 : per 1 speaker
∗
3 : use 2 speakers
Note: 1. Specifications are subject to change
without notice.
2.
Total harmonic distortion is measured by
the digital spectrum analyser.
3.
Total harmonic distortion is measured by
using AES17 filter.
MAIN UNIT
Power supply differ depending on the symbols (E, GN, GS) indicated on the packaging box.
