Radio operations
RQT7700
24
Manual tuning
1
Press [TUNER/AUX] (main unit: [BAND, TUNER]) to
select “FM” or “AM”.
The unit comes on.
Every time you press the button:
FM
→
→
AM
AUX
2
Press [
(
] or [
)
] (main unit: [
g
, REW/
4
4
4
4
4
] or
[
f
,
3
3
3
3
3
/FF]) to select the frequency.
Press and hold [
(
] or [
)
] (main unit: [
g
, REW/
4
] or
[
f
,
3
/FF]) until the frequency starts scrolling to start automatic
tuning. Tuning stops when a station is found.
“TUNED” is displayed when a radio station is tuned.
“ST” is displayed when a stereo FM broadcast is being received.
L
L
L
L
L
If noise is excessive in FM
Press [PLAY MODE] to display “MONO”.
Monaural sound is selected and noise reduces when reception is
weak.
Press [PLAY MODE] again to cancel the mode.
“MONO” is also canceled if the frequency is changed.
The radio
L
L
L
L
L
AM allocation setting
(main unit only)
For Saudi Arabia, Kuwait, the Middle East, South Africa and Southeast Asia
The step is factory-set to 9 kHz, but you can change it to receive
broadcasts allocated to 10 kHz steps.
1. Select “FM”.
2. Press and hold [BAND, TUNER].
After a few seconds the display changes to show the current
minimum frequency. Continue to hold the button down. The minimum
frequency changes and the step is changed.
To return to the original step, repeat the above steps.
Note
After changing the “allocation” setting, the frequencies you previously
preset in the memory will be cleared. Preset them again.
Preset tuning
There are two methods of pre-setting stations.
Automatic presetting
:All the stations the tuner can receive are
preset.
Manual presetting
:You can select the stations to preset and
the order they are preset in.
Up to 15 stations each can be set in the FM and AM bands.
Preparation:
Press [TUNER/AUX] (main unit: [BAND, TUNER]) to select “FM” or
“AM”.
Automatic presetting
Do the following once each for FM and AM.
Preparation:
Tune to the frequency where pre-setting is to begin.
Press and hold [PROGRAM] until the frequency
changes.
The tuner presets all the stations it can receive into the channels in
ascending order.
•
“SET OK” is displayed when the stations are set. The last station
to be set is then played.
“ERROR” is displayed
Presetting was unsuccessful. Preset manually.
Manual presetting
Pre-set the stations one at a time.
1
Tune to the station
(
A
see left).
2
Press [PROGRAM].
3
While “PGM” is flashing on the display
Press the numbered buttons to select a channel.
Alternatively, press [
g
,
4
] or [
f
,
3
] (main unit:
[
g
, REW/
4
] or [
f
,
3
/FF]) then press [PROGRAM].
The station occupying a channel is erased if another station is
preset in that channel.
Selecting channels
1
Press [TUNER/AUX] (main unit: [BAND, TUNER] to
select “FM” or “AM”.
2
Press the numbered buttons or [
g
,
4
4
4
4
4
] or [
f
,
3
3
3
3
3
]
to select the channel.
SKIP
PLAY MODE
TUNER/AUX
Numbered
buttons
BAND
TUNER
PROGRAM
REW/
,
, /FF
RQT7700(24-26)2
5/14/04, 9:02 AM
24
