Panasonic PV-M2738 Operating, Руководство по обслуживанию

Страница: 9 / 151

1-7
VCR Plus+ Setup
Channel Setup Preparations
NOTE:
Complete the steps on this page if your Combination
VCR hook-up resembles B .
Prepare a list like the example below.
This list will help you smoothly enter the information
needed in step d at right.
You will need the following to complete the list:
¥ A line up of normal and/or cable stations you
receive along with the channel numbers your TV
receives them on. A cable channel line-up chart is
supplied by your cable company.
¥ A list of Guide (VCR Plus+) channel numbers
assigned to the stations you receive. This list is
available in TV Guide and the TV listings found in
selected newspapers.
1
Make a chart with 3 columns like the example
below. In the left column, fill in the name or call
letters of the stations you receive.
2
In the middle column, fill in each station s
assigned Guide (VCR Plus+) number found in TV
Guide, newspapers, etc.
3
In the right column, fill in the channel number that
your TV receives the station on from your channel
line-up.
In order for the Combination VCR to read the VCR Plus+ code, some setup is required. A Guide (VCR Plus+) channel
number is assigned to each local broadcast and cable station. Because this number sometimes differs from the channel
your TV receives the station on, it is necessary to program the Combination VCR with local channel information.
ADD/
DELETE
Broadcast or
Cable Station
Name
HBO
Nickelodeon
CBS
FOX
Assigned Guide
(VCR Plus+)
Channel No.
33
38
34
11
Channel No. your
TV receives the
station on
15
20
04
< EXAMPLE ONLY >
VCR Plus+ Channel Setup
For Connection Type B only
¥ Before you begin, complete the Channel Setup
Preparations below left.
Important Note:
If your Combination VCR Connection type changes, from
Type A to B, repeat step 4 of previous page, select NO.
a
Press MENU to display
the MAIN MENU.
b
Press to
select CH, and then
press MENU to display
the SET UP CHANNEL
screen.
c
Press to select
VCR Plus+ CH SET
UP, and then press
to display the VCR
Plus+ CH SET UP
screen.
IMPORTANT NOTE:
For step d , use the list you prepared at left.
You may leave lines blank if you don t receive
that station, or if the GUIDE CH number and the
CATV (or TV) CH numbers are the same.
d
Press to move the
shaded area to the right
side.
Then, press to change the CATV (or TV) CH
number.
Next, press
to set the CATV (or TV) CH number.
Now, press to continue. Repeat this operation
until the list is complete.
To Make Corrections
Press
and to select the incorrect CATV or TV
CH number.
Then, press
to change, or ADD/DLT to delete the
channel.
e
Press MENU three times to exit the VCR Plus+
CH SET UP mode.
¥ Make each entry within 5 minutes or the
Combination VCR will leave this mode.
¥ Once local channels have been
programmed, they will stay in memory, even
in the case of a power failure.
2
¥
3
¥
4
¥
5
¥
b
¥
c
¥
d
1
¥
2
¥
6
¥
a
¥
b
¥
e
Cable Box Setup
For Connection Type A (see left) only
1
Press MENU* to display the
MAIN MENU.
2
Press to select
CH, and then press MENU
to display the SET UP
CHANNEL screen.
3
Press to select CABLE
BOX SET UP, and then
to set.
4
Press and to select
YES or NO, and then
press to set.
Select YES if all channels are
received via the cable box
(connection A at left ). Then, go
to step 5.
Select NO if your cable connection resembles B at
left. Press MENU to exit.
5
Press to select Cable
box output channel number,
and then press
to enter.
¥ If necessary, refer to your cable
box manual.
¥ If you are using Audio/Video jack
connection for your cable box,
select and set VIDEO OUT as
the output channel.
6
Press MENU twice to end the setup and return to
the normal screen.
Go directly to VCR Plus+ Programming.
VCR Plus+ programming allows you to set most items of a timer recording by simply entering a special code (PlusCode)
found in
TV GUIDE magazine as well as the TV listings in selected newspapers. In order for your Combination VCR to do a
VCR Plus+ recording, or a timer recording of cable stations, some setup is required.
At first, choose your Connection
Type.
(Then, follow the instructions under the diagram.)
Connection Type A
<CABLE BOX COMBINATION VCR>
If your system looks like this, do the
following.
1. Complete the Cable Box Setup
section at right.
2. Go directly for VCR Plus+
Programming.
Connection Type B
<CABLE or ANTENNA COMBINATION VCR>
If your system looks like this, do the
following.
1. Skip the Cable Box Setup
section at right.
2. Complete the VCR Plus+ Channel
Setup section.
3. Turn to VCR Plus+ Programming.
VCR Plus+ and PlusCode are
trademarks of Gemstar Development
Corporation.
The VCR Plus+ system is manufactured
under license from Gemstar Development
Corporation.
¥ This display appears for
5 seconds. (Channel
shown is example only)
*Important:
If the remote control POWER, CH
, MENU, PROG, ON-TIMER, R-TUNE, FM/TV and ADD/DLT button does not work
when pressed, press the MAIN button on the remote control and try the button again.
2
Cable Box Universal Remote Control Operation
2
The clock is set.
VCR Plus+ Setup is complete.
Before you begin, make sure...
The Remote Control may be set up to
control some of the functions on your
Cable box.
The remote control is
designed to control the
brands listed. However,
it will not operate all
Cable boxes made by
these manufactures. If
you get no results, your
particular product brand
cannot be controlled by
this remote.
Cable Box Brand Code Numbers
Universal Remote Control Setup
1
Find your Cable box brand code number from the
chart at the bottom of this page.
2
While holding down CATV, use the NUMBERED
keys to enter your Cable box brand code number.
¥ For code numbers 100 or greater, first press the 100 key, and then enter
the remaining digit. E.g., for 102, press 100, then press 2.
3
To confirm that the correct code was entered, press
POWER to turn your Cable box on/off.
4
Try each of the functions listed under Set to CATV :
in the following section.
¥ Due to changes in infra-red commands used by some manufactures,
more than one code may be listed for some Cable box brands. If your
Cable box does not respond to the first code, please try entering the
next code.
Using the Universal Remote Control
Once the remote control has been properly setup, you can select MAIN or
CATV mode depending on which functions you wish to control. (See
below.)
Press MAIN or CATV on the remote control to select the
desired mode. (See below for a list of controllable functions
for each mode.)
Set to MAIN:
¥All TV and VCR functions
Set to CATV:
¥Power
¥ Numbered keys ¥Channel Up/Down
¥ENTER ¥ Basic VCR functions, e.g. PLAY, REC, etc.
NOTES:
¥ In CATV mode, it may be necessary to press ENTER after pressing the
NUMBERED keys for channel selection.
¥ In CATV mode, ADD/DLT, MENU, PROG, ON-TIMER, R-TUNE and
FM/TV are not available. Press MAIN to use these functions.
¥ Depending on your Cable box brand, some of the functions listed may not
be remote controllable.
Archer .................... 01, 29, 44, 88, 91
Cableview ..04, 30, 42, 44, 52, 63, 85, 88
Citizen ....04, 30, 42, 44, 52, 63, 85, 88
Curtis ..................08, 09, 56, 61, 87, 90
Diamond ..................01, 29, 44, 88, 91
Drake....................................37, 67, 71
Eagle ......13, 20, 22, 26, 40, 58, 62, 98
Eastern ............................................28
GC Brand ..04, 30, 42, 44, 52, 63, 85, 88
Gemini ........................................04, 85
General Electric................................57
General Instruments ............................
01, 02, 03, 04, 34, 55, 83, 85, 91, 93, 95
Hamlin ......14, 15, 28, 41, 97, 100, 102
Jerrold ..................................................
01, 02, 03, 04, 34, 55, 83, 85, 91, 93, 95
Macom........................................31, 79
Magnavox ..................................25, 26
Matsushita ..........................16, 17, 101
Movietime ..29, 32, 38, 39, 40, 42, 44, 88
NSC......................................32, 38, 40
Oak ................................10, 11, 46, 99
Panasonic ..........................16, 17, 101
Philips ......................13, 20, 23, 24, 96
Pioneer ................................05, 06, 78
Pulsar ....04, 30, 42, 44, 52, 63, 85, 88
Radio Shack ....................................44
RCA....................................16, 17, 101
Realistic................................44, 51, 88
Regal ..........................................14, 41
Regency ..........................................28
Rembran ............29, 32, 39, 42, 44, 88
Salora ........................................68, 72
Samsung ..................32, 40, 42, 78, 94
Scientific Atlanta ....08, 09, 56, 61, 87, 90
Sheritech ..........................................27
SL Marx ....................32, 40, 42, 78, 94
Sprucer ..............................16, 17, 101 Stargate................................................
04, 30, 32, 40, 42, 44, 52, 63, 78, 85, 88, 94
Sylvania............................................19
Teknika ............................................74
Telecaption ................................77, 92
Teleview ..................32, 40, 42, 78, 94
Texscan......................................18, 19
Tocom ..........01, 33, 34, 42, 48, 49, 91
Toshiba ............................................36
Uniden Satellite ..........................65, 69
Unika ........................01, 29, 44, 88, 91
Universal ............42, 43, 44, 52, 63, 88
Viewstar..13, 20, 22, 26, 40, 58, 62, 98
Videoway..............................07, 23, 50
Vid Tech ..........................................64
Vidter ................................................64
Zenith ..................................07, 23, 50
CATV
MAIN
3
ENTER
Use normal Timer Recording
steps if:
¥the PlusCode for a program is
not listed.
¥you anticipate the program, such
as a sporting event, to run over
the scheduled stop time.
¥cancel a timer recording in
progress.
¥replace program contents.
¥review or clear program contents
once set.
PROGRAM TIMER Indicator
¥ You can obtain unlisted PlusCode numbers by calling
1-900-454-7587. Call costs approximately $.95 per minute.
¥ Avoid overlapping program times.
¥ An on-screen display will indicate if an invalid PlusCode
number has been entered or when all timer programs
are full.
ADD/
DELETE
SPEED
VCR Plus+ Programming
2
¥
6
5
3
1
¥
4
¥
6
¥
7
1
Press PROG* to display the SET
PROGRAM screen.
2
Press to select VCR
Plus+ PROGRAM and then
press
to display the Plus
Code screen.
3
Press NUMBERED keys to enter
the PlusCode number from your
local TV listings.
To Make Corrections
Press
repeatedly to delete the PlusCode
number. Then, enter the correct number.
4
Press PROG to lock in your program.
5
Press the 1, 2, or 3 key to select
the program type.
To Change the Recording Speed
Press SPEED for SP, LP, SLP.
To Chancel Program Contents
Press ADD/DLT.
¥ If you use connection type A , the channel
shown in this on-screen display will always be
the cable box output channel number.
6
Press PROG to end the program.
¥ This screen appears for confirmation.
7
Press PROG twice to exit this
mode and return to the normal
screen.
¥ The PROGRAM TIMER indicator lights on
the front panel.
¥ If you re using a cable box, make sure that
it is tuned to the desired channel and the
power is left on for timer recording.
¥ This display appears if
you use a cable box.
*Important:
If the remote control POWER, CH
, MENU, PROG, ON-TIMER, R-TUNE,
FM/TV and ADD/DLT button does not work when pressed, press the MAIN
button on the remote control and try the button again.