Panasonic PT47WXD63G - 47" PROJECTION TV Скачать руководство пользователя страница 76

Страница: 76 / 197

29. Perform adjustments for red so that red overlaps green, do not

move green.

30. Press “1 or 3” on the remote until yellow (red and green) and blue

appears, do not move green or red.

31. Perform adjustments so that blue overlaps Yellow (red and green).

32. Press “1 or 3” key on remote to display red, green and blue

(white).

33. At this point the crosshatch pattern should look white.

34. If the crosshatch pattern is not only white, repeat adjustment for

that specific color (red or blue).

35. Once the crosshatch pattern looks only white, perform the

adjustments for White only (“POINT”, “ORIG. POINT” & “LINE”),
notice that each adjustment must be only for white (red, green,blue)

36. Adjust white for a good line distribution and make lines

completely straight.

37. Press “7” key on remote, then OK to save changes.

38. Press POWER then OK to exit convergence adjustments (DACs

menu appears).

18.3. Horizontal and vertical size check

1. Apply a pattern that permits to check that horizontal and vertical

proportion of the image is correct

2. Confirm that horizontal and vertical center of the picture is located

in the center of the screen.

3. Check that the image is proportional horizontally and vertically,

proportion is different on every aspect.

Содержание PT47WXD63G - 47" PROJECTION TV






































































































































































































Результаты поиска

Содержание PT47WXD63G - 47" PROJECTION TV

Отзывы:

Похожие инструкции для PT47WXD63G - 47" PROJECTION TV

Бренды по названию

Популярные бренды

Panasonic PT47WXD63G - 47" PROJECTION TV, Руководство по обслуживанию

Результаты поиска

Содержание PT47WXD63G - 47" PROJECTION TV

Отзывы:

Похожие инструкции для PT47WXD63G - 47" PROJECTION TV

Бренды по названию

Популярные бренды