Panasonic PT47WXD63G - 47" PROJECTION TV Скачать руководство пользователя страница 51

Страница: 51 / 197

9. Set VIDEO “C_OFF” DAC from 01 to 02 to project only red.

10. Adjust red deflection coil until the horizontal center line matches

the pattern of the grid and is leveled.

11. Adjust red centering magnets until the pattern center is at the

appropriate distance as indicated on figure.

12. Enable digital convergence by changing DAC MUTE from 01 to 00.

13. Set VIDEO “C_OFF” DAC from 02 to 00. Following the adjustment,

make sure that all deflection coils are pushed completely toward
the CRT cones and that all screws are tightened.

17.3. Vertical linearity adjustment (V-C and V-S)

This adjustment is intended to make the picture vertically proportional (top, center and bottom)

NOTE:
1080i, 480p, 480i pattern can be obtained from Panasonic’s TU-DST51 set-top box DTV decoder.

1. Apply a pattern that lets adjust the image to correct vertical

linearity (see above note).

2. Set VIDEO “C_OFF” DAC from 00 to 01 (to project only green).

3. Set DAC MUTE from 00 to 01 (disabling digital convergence).

4. Adjust centering magnets so that the center of the pattern get

aligned with screen frame center.

5. Adjust VDEF “V-C” and “V-S” DAC until vertical size is proportional

on top and bottom. Confirm to correct linearity in the middle of the
screen.

6. Set DAC MUTE from 01 to 00 (disabling digital convergence).

7. Set VIDEO “C_OFF” DAC from 01 to 00

Содержание PT47WXD63G - 47" PROJECTION TV






































































































































































































Результаты поиска

Содержание PT47WXD63G - 47" PROJECTION TV

Отзывы:

Похожие инструкции для PT47WXD63G - 47" PROJECTION TV

Бренды по названию

Популярные бренды

Panasonic PT47WXD63G - 47" PROJECTION TV, Руководство по обслуживанию

Результаты поиска

Содержание PT47WXD63G - 47" PROJECTION TV

Отзывы:

Похожие инструкции для PT47WXD63G - 47" PROJECTION TV

Бренды по названию

Популярные бренды