Panasonic PT47WXD63G - 47" PROJECTION TV Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 197

background image

2. Select TIMER icon and set SLEEP time for 30 Min.

3. Press “OK” then VOL up to exit menus.

4. Tune to the Channel 124.

5. Adjust VOLUME to minimum (0).

6. Press VOL (decrease) on receiver. Red “CHK” appears in upper

corner.

To toggle between aging and service modes:
While the “CHK” is displayed on the left top corner of the CRT, pressing “OK” and “VOL” UP on
the TV simultaneously will toggle between the modes. Red “CHK” for service modeand yellow
“CHK” for aging.

7. Press POWER on the remote control to display the service

adjustment modes menu, select adjustment by pressing the VOL
right/left buttons and CH up/down buttons on the remote and OK to
enter the adjustment.

Service mode menu

15.2. Exiting the service mode:

This PTV goes out from service mode when it is unplugged or turned OFF. To exit the service
mode, turn the TV OFF or unplug the PTV from AC.

Other method
Press  OK and POWER on the receiver simultaneously for at  least 2 seconds.The receiver
momentarily  performs  a self-check, tuned in channel 3 with a preset level of sound. To
completely  make an entire reset of the PTV unplug AC cord from AC outletand plug it back in,
then turn PTV power ON.Any programmed channels, channels  caption data and some others
user defined settings  will be erased when performing this  reset.

41

«
...
39
40
41
42
43
...
»

Содержание PT47WXD63G - 47" PROJECTION TV






































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PT47WXD63G - 47" PROJECTION TV

Бренд: Barco Страницы: 48

Бренд: Barco Страницы: 66

Бренд: Barco Страницы: 82

Бренд: Barco Страницы: 6

Бренд: Barco Страницы: 2

Бренд: Barco Страницы: 78

Бренд: Barco Страницы: 8

Coronis 5MP Mammo

Бренд: Barco Страницы: 88

Color Coronis 2MP

Бренд: Barco Страницы: 2

Color Coronis 2MP

Бренд: Barco Страницы: 4

Бренд: Barco Страницы: 40

Бренд: Barco Страницы: 52

Бренд: Hantarex Страницы: 25

Бренд: jablotron Страницы: 84

Бренд: Quark-Elec Страницы: 2

Бренд: Vuescape Страницы: 33

Бренд: e-Ink Страницы: 18

Бренд: Fametech Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды