Panasonic PT47WXD63G - 47" PROJECTION TV Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 197

background image

front panel the next sequence rapidly:
VOLUME UP and MENU buttons at the same time, then CHANNEL
UP and MENU buttons at the same time.

6. A status screen will appear displaying information about the

System status.

7. The “System” information displays the current software version,

release date, memory and POD status.

8. If the CableCARD is operating properly the POD status will indicate

that the CableCARD is present. If the CableCARD is inserted and
the POD status indicates that is not present, the CableCARD could
be damaged.

9. To exit the system status screen, press exit.

10. Remove the CableCARD and check that a sign on the screen

appears indicating that the card has been removed.

18. Convergence adjustment

Turn PTV on and allow it to warm up for 30 minutes prior to perform adjustments (apply a
WHITE PATTERN).

Helpful Hint:
EEPROM jig can be used to adjust convergence, by copying convergence adjustment from a
convergence adjusted PTV to other. Refer to EEPROM copy jig section on this service manual.
Also EEPROM copy jig can be used to back-up the data before to performadjustments.

NOTE:
1080i, 480p, 480i pattern can be obtained from Panasonic’s TU-DST51 set-top box DTV decoder.

IMPORTANT NOTICE:
It is strongly recommended to first read and understand the following section prior to make any
adjustment.

This PTV uses the scheme described below to correct for misconvergence of the three CRT
projection tubes. There are various modes to this operation.

Preparation:
Place the convergence alignment  template (see Convergence alignment  template section on
this  manual)  over the PTV screen. Align the center lines  of the template with the mechanical
center markers  on the PTV screen frame. If the template is  not available,create one using the
dimensions  provided in Convergence alignment  template section on this  manual.Remote
control must be used during the procedure.

63

«
...
61
62
63
64
65
...
»

Содержание PT47WXD63G - 47" PROJECTION TV






































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PT47WXD63G - 47" PROJECTION TV

MultiSync EA245WMi-BK

Бренд: NEC Страницы: 30

Бренд: Excel Technology Страницы: 7

Бренд: I-Inc Страницы: 20

Бренд: Swann Страницы: 2

Бренд: HANNspree Страницы: 24

Бренд: Maxent Страницы: 1

Бренд: Jimi Страницы: 33

Бренд: NA-DE Страницы: 4

Бренд: Mottura Страницы: 40

Бренд: NCI Страницы: 4

Бренд: Counterline Страницы: 15

Бренд: Kodak Страницы: 28

Poly Medialign 65

Бренд: Plantronics Страницы: 157

Бренд: Neotec Страницы: 22

Бренд: FDS Страницы: 16

Бренд: CA Traffic Страницы: 2

Бренд: NEC Страницы: 25

A2T-6508-AD-10U

Бренд: Activ2Touch Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды