Panasonic PT47WXD63G - 47" PROJECTION TV Скачать руководство пользователя страница 65

Страница: 65 / 197

12. Press “TV/VIDEO” key on remote to enter “OSD_POS” mode.

13. Press “5” key on remote so that monoscope pattern appears

(superimpose mode)

14. Move cursor by pressing VOL right - left and CH up - down so that

cursor center overlap monoscope pattern center

15. Press “0” key to go back to “Coarse adjustment” mode.

16. Press “TV/VIDEO” key to cycle through “Coarse adjustment”

options

“COARSE” modes cycle

17. To change to “Fine Adjustment Mode” options (“FINE” DAC),

press “TV/VIDEO” key on remote for at least 3 seconds, to go back
to “Coarse
Adjustment Mode” options press “TV/VIDEO” on remote again for 3
seconds.

18. In “Fine Adjustment Mode” options, press “MUTE” key on remote

to switch between “cursor” mode and “data” mode.

- Cursor mode: Allows cursor movement by pressing VOL right -

left and CH up - down.

- Data mode: Allows making adjustment by pressing VOL right -

left and CH up - down.

19. Either “Coarse Adjustment” options or “Fine Adjustment” options,

press “R-TUNE” repeatedly key on remote to cycle through
different color adjustments (R, G, B, White)

20. In “Fine Adjustment” options, press “4” key on remote to ADD

crossed sections to pattern and make effect visible between
crossed sections.

Содержание PT47WXD63G - 47" PROJECTION TV






































































































































































































Результаты поиска

Содержание PT47WXD63G - 47" PROJECTION TV

Отзывы:

Похожие инструкции для PT47WXD63G - 47" PROJECTION TV

Бренды по названию

Популярные бренды

Panasonic PT47WXD63G - 47" PROJECTION TV, Руководство по обслуживанию

Результаты поиска

Содержание PT47WXD63G - 47" PROJECTION TV

Отзывы:

Похожие инструкции для PT47WXD63G - 47" PROJECTION TV

Бренды по названию

Популярные бренды