Panasonic PT-DW740, Руководство по эксплуатации

Страница: 79 / 133

ENGLISH - 79
Chapter 4 Settings — [PROJECTOR SETUP] menu
9)
Press
qw
to switch [COMMAND].
r f
The setting will change among [POWER ON], [STANDBY],
[SHUTTER] *1 , [INPUT] *1 , [LAMP SELECT] *1 , [LAMP POWER] *1
and [SIDE BY SIDE] *1*2 each time you press the button.
*1 The details set in step 11) are displayed.
*2 Only for PT-DW740E
10)
Press the <ENTER> button.
r f
The [COMMAND] detailed screen is displayed.
11)
Press
as
to select a command.
r f
[OPEN]/[CLOSE] in [SHUTTER], [RGB1]/[RGB2]/[VIDEO]/
[S-VIDEO]/[DVI-D]/[HDMI] in [INPUT], [DUAL]/[SINGLE] in
[LAMP SELECT], [NORMAL]/[ECO] in [LAMP POWER], and
[OFF]/[ON] in [SIDE BY SIDE] will change each time you press
qw
.
12)
Press the <ENTER> button.
r f
The command is fixed and ● is displayed at the left of the
selected command.
r f
After the command is fixed, press the <MENU> button to close
the detailed setting menu.
13)
Press
as
to select [STORE], and press the
<ENTER> button.
r r
[COMMAND]
[POWER ON] ― Turns the power on.
[STANDBY] ―
Enters standby.
[SHUTTER]
[OPEN] Opens the shutter.
[CLOSE] Closes the shutter.
[INPUT]
[RGB1] Switches the input to RGB1.
[RGB2] Switches the input to RGB2.
[VIDEO] Switches the input to VIDEO.
[S-VIDEO] Switches the input to S-VIDEO.
[DVI-D] Switches the input to DVI-D.
[HDMI] Switches the input to HDMI.
[LAMP SELECT]
[DUAL] Turns on both lamps.
[SINGLE]
Turns on one lamp. (The lamp is automatically selected which has shorter
cumulative operating time.)
[LAMP POWER]
[NORMAL] Sets the high luminance of the lamp.
[ECO] Sets lower luminance of the lamp than [NORMAL].
[SIDE BY SIDE]
*
[OFF] Displays the side-by-side screen.
[ON] Cancels the side-by-side screen.
* Only for PT-DW740E
Note
r f
If you try to register a setting that would cause the lamp to flash for a short time, an error message will be displayed on the screen. Set the
time and command again.
r f
To delete a command already set, press the <DEFAULT> button on the Step 5) screen, or select [DELETE] on the Step 6) screen and press
the <ENTER> button.
r f
If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
r f
The operating time will be the local time. (
x
page 83)
r f
If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with this function may not be executed.
[STARTUP INPUT SELECT]
Set the input signal to be projected when the projector is switched on.
1)
Press
as
to select [STARTUP INPUT
SELECT].
2)
Press
qw
to switch [STARTUP INPUT
SELECT].
r f
The setting will change among [LAST USED], [RGB1], [RGB2],
[VIDEO], [S-VIDEO], [DVI-D] and [HDMI] each time you press
the button.
r r
[STARTUP INPUT SELECT]
[LAST USED] Keeps the input selected last.
[RGB1] Sets the input to be projected when the projector is switched on to RGB1.
[RGB2] Sets the input to be projected when the projector is switched on to RGB2.
[VIDEO] Sets the input to be projected when the projector is switched on to VIDEO.