Panasonic MCCG467 - CANISTER VAC - MULTI LANGUAGE, Руководство по эксплуатации

Страница: 5 / 12

5
C-1 Pull out the mains lead and put the plug into the
socket outlet.
C-2 Gently press at the centre of the switch pedal to
turn ON the vacuum cleaner.
Press the pedal again to turn it OFF.
C-3 Power control
To increase or decrease the power, turn the variable
power control button.
C-4 Switching 3 positions.
Flooring (PARQUET): Set position A
Carpet (short): Set position B
Carpet (long or hard to push): Set position C
C-5 The curved wand of the hose is attached with a
manual suction regulator, which allows you to briefl y
reduce the suction level.
C-6 After you fi nish vacuuming, remove the plug from
the wall socket and press the cord rewind pedal.
When rewinding the power cord, press the cord
rewind pedal by holding the plug so that it does not
become damaged.
C-7 Storage position
Slide the wand holder attached to turbine nozzle pipe straight
into the wand supporter on the under side of the main body.
C-8 Park position
For short breaks during vacuuming, slide the wand
holder attached to the turbine nozzle pipe into the
wand supporter on the rear side of main body.
NOTE: When you use park position, we suggest the
appliance is switched off.
Indicator for replacing the dust bag
Turn the power control to the highest setting and lift the
nozzle off the fl oor. If the dust indicator turns red, the dust
bag is full and requires replace the dust bag.
NOTE: If the dust bag is not properly installed, the cover will
not close. Be sure to check that the bag is properly
installed before operating, otherwise dust will leak out.
The dust bag can easily lay on the dust cover packing
or clip between bag collar and body, so be sure to
properly extend it into the vacuum cleaner body.
Replacing the dust bag
D-1 Lift dust cover catch and raise dust cover until it
clicks properly.
D-2 Remove bag collar from bag holder and pull out
dust bag.
D-3 Set a new dust bag.
D-4 Close dust cover properly until you hear it click.
Turbine nozzle
D-5 After removing the brush cover with a coin, remove
the beater bar from the belt.
Then cut across threads, strings, hairs, etc. from the
beater bar with a pair of scissors. (Removal as per
reverse procedure)
NOTE: Take care not to cut the brush.
Do not wash in water.
CAUTIONS
• The plug must be removed from the socket-outlet
before cleaning or maintaining the appliance.
• To avoid injury, keep your fi ngers and hands away
from the beater bar.
• DO NOT use hot air or hot surface to dry fi lters. Keep
at room temperature for approximately 24 hours.
• IMPORTANT: Before re-installing the washable fi lters,
make sure they are completely dry to avoid damaging
the cleaner.
Vacuum cleaner body
D-6 Wipe with a soft cloth soaked with water.
Maintaining the Pre-motor Filter
Follow the procedure written below when the suction power
is not restored after replacing a new bag.
D-7 Open the dust cover.
D-8 Remove the pre-motor fi lter.
D-9 Wash gently with water and then allow to dry in a
shaded location.
D-10 Replace to its original location.
NOTE: Make sure you remember to replace the fi lter. If the
fi lter is not installed, it will cause motor failure.
• Do not wash the fi lter in a washing machine or dry it with a
dryer or other source of hot air.
Filter care
D-11 Exhaust fi lter
Exhaust fi lter is installed in the rear side of the
vacuum cleaner. This fi lter retains any small dust
particles which may be present in the expelled air.
It is advisable to change the fi lter once or twice a
year, depending on use. To change the fi lter, hold
the exhaust cover (as illustrated) and pull it out. After
changed the fi lter, set the exhaust cover to its position
(as illustrated).
NOTE:
IMPORTANT: Never use the cleaner without the correct
fi lters properly installed. Failure to do so may
result in damage to the motor.
What to do if your cleaner does not work
Check that the appliance is correctly plugged in and that the
electrical socket is working. In case that the thermal cut-out
device has operated, wait until it resets after approximately
60 minutes. If after having checked the mentioned points, the
cleaner does not work, take it to an Authorized Service Centre to
be repaired.
What to do when the suction performance
reduces
What to do when the suction performance What to do when the suction performance
• Stop the cleaner and unplug from the socket.
• Check whether the wands, hose and accessories are blocked or
not. If they are blocked, remove the obstruction.
• Check that the dust bag is full. If it is full, replace it to a new
one.
• Check that Pre-motor Filter or Exhaust Filter is blocked with
dust. If they are blocked, clean them out or replace.
SPECIFICATIONS MC-CG467
POWER SOURCE AC120V ~ 60Hz
CURRENT 11Amps
AUTOMATIC CORD REWIND YES
DUST BAG PAPER
DUST CAPACITY 3.0L
CORD LENGTH 5.0m (16Ft.)
EXTENSION WANDS METAL TELESCOPIC
NOZZLE 3 in 1 TURBINE NOZZLE
WEIGHT (WITH
ACCESSORIES)
4.5 k g (9.9lbs.)
DIMENSIONS
(W×L×H)
280mm×425mm×260mm (11in×16.7in×10.2in)
ACCESSORIES NOZZLE CREVICE NOZZLE & DUSTING BRUSH
REMINDER FOR CUSTOMER
The model and serial number of this product may be found on the
nameplate located at the underside of your cleaner. You should
note the model and serial number in the spaces provided and
retain this book as a permanent record of your purchase.
Model Number. .............................................................................
Serial No. ......................................................................................
Date Purchased. ...........................................................................
Where Purchased. ........................................................................
C - HOW TO OPERATE YOUR CLEANER
D - MAINTENANCE AND SERVICING