manualshive.com logo in svg

Panasonic KX-TG2581ALS, KX-TG2581NZS, Руководство по эксплуатации, Страница: 21 / 80

Поделиться
Скачать
Panasonic KX-TG2581ALS, KX-TG2581NZS Скачать руководство пользователя страница 21

Preparing the Answering System

21

Preparation

To increase the volume, 
press VOLUME

.

To decrease, press
VOLUME

.

Greeting message sample

“Hello, this is (your name and/or number). Sorry I cannot take your
call. Please leave a message after the beep. Thank you.”

Greeting Message

You can record a personal greeting message of up to 2 minutes. If a
greeting message is not recorded, one of two pre-recorded greetings will
be played when a call is received (p. 22).

The total recording time of all messages (greeting, incoming) is about
15 minutes. We recommend you record a brief greeting message
(see sample below) in order to leave more time for recording new
messages.

To record a greeting message

1

Press and hold 

(GREETING)

until

“

Record greeting after the beep

” is

heard.

2

Talk clearly, about 20 cm away
from the MIC (microphone).

•

The base unit display shows the
elapsed recording time.

•

If you record for over 2 minutes,
the unit will automatically stop
recording.

3

When finished, press 

(STOP)

.

•

To check the recorded greeting, 
press 

(GREETING)

briefly.

•

To change the message, 
start again from step 1.

(GREETING)

(STOP)

(ERASE)

MIC

Содержание KX-TG2581ALS, KX-TG2581NZS

















































































Отзывы:

Нет отзывов