manualshive.com logo in svg

Panasonic KX-TD500CE, Руководство по функциям, Страница: 12 / 376

Поделиться
Скачать
Panasonic KX-TD500CE Скачать руководство пользователя страница 12

1.2

System Administration

12

Features Guide

(Method 3.) Using an external modem
Please refer to "External Modem Control" in Section "1.3

System Features," and Section 

"2.11.1 Controlling the External Modem (External Modem Control)" in the User Manual.

For more information and programming instructions, please refer to the Installation Manual 
and the Programming Guide.

Conditions

•

One Time One Access
Access to System Programming is allowed only one device at a time.

•

System Password
To access system administration, a valid password must be entered. The password is 
factory-programmed and can be changed.

•

System administration can be performed on-line except for the procedures of the diagnosis.

Installation Manual References

•

2.6.2 ERMT Card (KX-TD50197)

Programming Guide References

•

10.2 External Modem 1/2

•

10.3 External Modem 2/2

•

10.6 System Parameters

– [Password] System Programming
– [Serial Interface Port] PROG – Parity
– [Serial Interface Port] PROG – NL Code
– [Serial Interface Port] PROG – Word Length
– [Serial Interface Port] PROG – Stop Bit
– [Serial Interface Port] PROG – Baud Rate

Features Guide References

1.3

System Features

•

External Modem Control

User Manual References

Not applicable.

Содержание KX-TD500CE

























































































































































































































































































































































































Отзывы:

Нет отзывов