manualshive.com logo in svg

Panasonic KX-TD500CE, Руководство по функциям, Страница: 32 / 376

Поделиться
Скачать
Panasonic KX-TD500CE Скачать руководство пользователя страница 32

1.3

System Features

32

Features Guide

External Modem Control

Description

The system supports an external modem (see Notes) plugged into the RS-232C Port 1. The 
system communicates with the remote terminal at data rate of up to 19,200 bps and enables 
remote system maintenance through an external modem. A pre-assigned AT Command (see 
Notes) can be sent to an external modem automatically when it is plugged into the RS-232C 
Port 1. The extension user is also allowed to control the external modem by sending the pre-
assigned AT Commands.

Conditions

•

To connect an external modem to your system, perform the following procedures:

1.

Connect the modem to the system with the EIA (RS-232C) cable. 

2.

Connect the modem to an extension port which is assigned as the DIL 1:1 destination. Or 
connect the CO line directly to the modem.

3.

Set the power switch of the modem to "ON," then the modem will be initialised with the 
default values.

4.

The following AT Command programming may be required for the modem.

•

The Data Terminal Ready (DTR) signal should be ignored.

•

The Data Terminal Equipment (DTE) / Modem flow control should be turned off.

•

The data compression should be disabled.

•

Error Correction is not necessary.

Notes

•

Not all modems will be compatible. Please contact the Panasonic Bulletin Board 
System (BBS).

•

Please refer to the modem instructions as the AT Commands depend on the 
manufacturer of your model.

•

The connection chart for the external modem (25-pin) is as follows:

DIGITAL SUPER HYBRID SYSTEM

RUN

OFF LINE

ALARM

PBX

RS-232C Port 1

 To PBX extension
 or CO line

Modem

Serial Interface (25-pin)
 (RS-232C)

Содержание KX-TD500CE

























































































































































































































































































































































































Отзывы:

Нет отзывов