Panasonic KX-TCD961EB Скачать руководство пользователя

Страница: 45 / 68

Chapter 4

Answering System

To continue the remote operation

When listening to your messages remotely, the unit will stop playback every 2 minutes and 40 seconds
and you will hear two beeps.
To continue playback, press

within 10 seconds after the beeps. If you do not press

within that

time, the unit will hang up. All messages will be saved.

Skipping the greeting message

After calling your unit, press

during the greeting message.

•

The unit skips the rest of the greeting message and you can start recording your message after the
long beep.

Remote Operation with the Handset

You can operate your answering system with the handset.
The announcements and recorded messages can only be heard from the handset.

Summary of remote operation

Press

then

•

The number of new messages is heard.

•

“

” is displayed on the handset.

INT

Enter the desired direct commands (p. 46).

•

If you do not enter a command, the voice
menu will start.*

•

After the voice menu, all message
playback will start.

To end the remote operation, press

•

The messages are saved.

•

If you hear “

Memory is full

” after playback,

erase some or all of the messages (p. 46).

*Voice menu

If no commands are entered after you press

and

, the unit will start the following

voice menu:

“

Press 4 to playback new messages. Press 5 to

playback all messages.

”

•

You can enter direct commands even when
the voice menu has started.

INT

KX-TCD961EB.4(38~46) 99.9.27 7:33 PM Page 45

Содержание KX-TCD961EB





































































Результаты поиска

Содержание KX-TCD961EB

Отзывы:

Похожие инструкции для KX-TCD961EB

Бренды по названию

Популярные бренды

Panasonic KX-TCD961EB, Руководство по эксплуатации

Результаты поиска

Содержание KX-TCD961EB

Отзывы:

Похожие инструкции для KX-TCD961EB

Бренды по названию

Популярные бренды