Panasonic KX-TCD725EM Скачать руководство пользователя страница 94

Страница: 94 / 100

Before Requesting Help

Problem

The unit does not work.

You cannot program items such as the
time/day adjustment.

The battery strength is not displayed
correctly.

“

” flashes or the unit beeps every

15 seconds.

You charged the batteries fully, but
“

” flashes.

Remedy

•

Turn the power ON (p. 12).

•

Check the settings (p. 54).

•

Charge the batteries fully (p. 11).

•

Clean the charge contacts and charge again (p. 11).

•

Unplug the AC adaptor and turn the power OFF to
reset. Plug in the AC adaptor and turn the power ON.
Then try again.

•

The handset has been cancelled or has not been
registered. Register the handset (p. 80).

•

Re-install the handset batteries and try again.

•

Programming is not possible while the unit is in the
talk or intercom mode.

•

Move closer to the base unit.

•

Check that the battery type selection is correct
(p. 52).

•

Charge the batteries fully (p. 11).

•

Clean the charge contacts and charge again (p. 11).

•

Install new batteries (p. 52, 86).

General

KX-TCD725EM-5(86~100) 01.7.19 10:22 PM Page 94

Содержание KX-TCD725EM





































































































Результаты поиска

Содержание KX-TCD725EM

Отзывы:

Бренды по названию

Популярные бренды

Panasonic KX-TCD725EM, Руководство по эксплуатации

Результаты поиска

Содержание KX-TCD725EM

Отзывы:

Бренды по названию

Популярные бренды