Panasonic KX-TCD725EM Скачать руководство пользователя страница 66

Страница: 66 / 100

Summary of Direct Command for Answering System Operations

See the corresponding pages for function details.

Make sure that the power is ON (p. 12), and the unit is in the standby mode.

B a s e 1 [ A ]

4 M e s s a g e s
0 N e w C a l l s

Press

(INT)

then

•

lights and voice guidance is heard from the speaker.

•

Message information is displayed for 2 seconds, then function menu is displayed.

•

A brief voice guidance indicates the number of new message received, then you can
hear “Press 4 to playback new messages” and “Press 5 to playback all messages.”

Press

To repeat an/a incoming/memo message during playback (p. 71)

Press

To skip an/a incoming/memo message during playback (p. 71)

Press

To select the receiver volume during playback (p. 73)

Press

To playback new incoming/memo message(s) (p. 69)

Press

To playback all incoming/memo message(s) (p. 69)

Press

To playback a greeting message (p. 13, 68)

Press

To record a memo message (p. 70)

Press

To record a greeting message (p. 67)

Press

To set the answering system ON (p. 13, 68)

Press

To stop the answering system operation (p. 71)

Press

To set the answering system OFF (p. 13, 68)

Press

To erase one incoming/memo message* (p. 69)

Press

To erase all incoming/memo message(s) (p. 70)

Press

To erase the recorded greeting message** (p. 68)

ALL

OFF

* These functions are available only during incoming/memo message playback.

** This function is available only during your own greeting message playback.

•

If each operation procedure is not completed within 30 seconds, the display will return to standby

mode.

KX-TCD725EM-4(65~85) 01.7.19 10:23 PM Page 66

Содержание KX-TCD725EM





































































































Результаты поиска

Содержание KX-TCD725EM

Отзывы:

Бренды по названию

Популярные бренды

Panasonic KX-TCD725EM, Руководство по эксплуатации

Результаты поиска

Содержание KX-TCD725EM

Отзывы:

Бренды по названию

Популярные бренды