Panasonic KX-TCD725EM Скачать руководство пользователя страница 36

Страница: 36 / 100

Special Features

Pause Feature

(For Analogue PBX Line/Long Distance Service Users)

We recommend you to insert “Pause” if a pause is required for dialling with a PBX or to access a long
distance service.
Make sure that the power is ON (p. 12), and the unit is in the standby mode.

P a u s e
G o B a c k

Ex. Line access number

(PBX)

Phone number

Press

then

Press

and press

to select “

Pause

”.

Enter a phone number.

•

Selecting “

Pause

” creates a pause. “

” is displayed.

This prevents misdialling when you redial or dial a stored number.

•

Selecting “

Pause

” more than once increases the length of the pause between numbers.

9 P 1 2 3 4 5 6 7

Key Lock

You can lock the handset dialling buttons. Only incoming calls are accepted while the key lock is ON .

Make sure that the power is ON (p. 12), and the unit is in the standby mode.

To set the key lock

Press and hold

until a beep sounds.

•

“

[X]

” is displayed and all dialling buttons are locked.

To cancel the key lock

Press and hold

for about 2 seconds.

•

“

[X]

” will disappear and the key lock will be cancelled.

•

The key lock will also be cancelled when the power is OFF (p. 12).

•

When the key lock is ON, emergency calls can not be made until the key lock is cancelled.

B a s e 1

[ X ]

1 0 N e w C a l l s

0 6 . 0 9 0 4 : 0 4 P M

KX-TCD725EM-2(24~37) 01.7.19 10:23 PM Page 36

Содержание KX-TCD725EM





































































































Результаты поиска

Содержание KX-TCD725EM

Отзывы:

Бренды по названию

Популярные бренды

Panasonic KX-TCD725EM, Руководство по эксплуатации

Результаты поиска

Содержание KX-TCD725EM

Отзывы:

Бренды по названию

Популярные бренды