8. Programmable Features
76
3.
Scroll to “
Set answering
” by pressing
{v}
or
{e}
, and press
{>}
.
4.
Scroll to “
Recording time
” by pressing
{v}
or
{e}
, and press
{>}
.
5.
Press
{v}
or
{e}
repeatedly to select the
desired setting.
L
You can also select the recording time by
pressing a dialing button
{
1
}
(1 minute),
{
2
}
(2 minutes),
{
3
}
(3 minutes) or
{
0
}
(“
Greeting only
”).
6.
Press the right soft key (
{
SAVE
}
).
7.
Press
{
OFF
}
.
Note:
L
If you select “
Greeting only
”, the unit will
answer a call with the greeting message, and
then hang up. The unit will not record any
incoming messages.
L
You can also program this feature with the
base unit (feature #10 on page 69).
Setting remote operation code
Make sure the base unit and the handset are
not being used.
1.
Press
{
CONF/FUNCTION
}
.
2.
Scroll to “
Initial setting
” by pressing
{v}
or
{e}
, and press
{>}
.
3.
Scroll to “
Set answering
” by pressing
{v}
or
{e}
, and press
{>}
.
4.
Scroll to “
Remote code
” by pressing
{v}
or
{e}
, and press
{>}
.
5.
Enter a remote code using a 2-digit number
(00–99).
L
The default setting is “
11
”.
6.
Press the right soft key (
{
SAVE
}
).
7.
Press
{
OFF
}
.
Note:
L
You can also program this feature with the
base unit (feature #11 on page 69).
Setting the mailbox 2 or 3 password
To prevent other users from retrieving your
messages, program a password for mailbox 2 or
3.
Make sure the base unit and the handset are
not being used.
1.
Press
{
CONF/FUNCTION
}
.
2.
Scroll to “
Initial setting
” by pressing
{v}
or
{e}
, and press
{>}
.
3.
Scroll to “
Set answering
” by pressing
{v}
or
{e}
, and press
{>}
.
4.
Scroll to “
Set mailbox2&3
” by pressing
{v}
or
{e}
, and press
{>}
.
5.
Select the mailbox by pressing
{e}
(“
Mailbox2
”) or
{v}
(“
Mailbox3
”).
L
If the password has previously been
assigned to the mailbox, it is displayed.
6.
Enter a 2-digit number (00–99).
L
If you entered a wrong number, press
{
HOLD/CLEAR
}
and enter the password
again.
7.
Press the right soft key (
{
SAVE
}
).
8.
Press
{
OFF
}
.
To check the password
Repeat steps 1 to 5.
L
The password is displayed. When finished,
press
{
OFF
}
.
To erase the password
Press
{
HOLD/CLEAR
}
in step 6, and press the
right soft key (
{
SAVE
}
), then press
{
OFF
}
.
L
You will be able to access the mailbox without
entering the password.
Note:
L
You can also program this feature with the
base unit (feature #51 on page 71 and
feature #52 on page 71).
Setting the room monitor feature
See page 48 for details. To turn ON the base unit
room monitor feature using the handset,
program as follows:
Use the handset. Make sure the base unit and
the handset are not being used.
1.
Press
{
CONF/FUNCTION
}
.
2.
Scroll to “
Initial setting
” by pressing
{v}
or
{e}
, and press
{>}
.
3.
Scroll to “
Set base unit
” by pressing
{v}
or
{e}
, and press
{>}
.
4.
Scroll to “
Room monitor
” by pressing
{v}
or
{e}
, and press
{>}
.
5.
Press
{v}
or
{e}
repeatedly to select the
desired setting.
6.
Press the right soft key (
{
SAVE
}
).
Note:
L
You can also set the base unit room monitor
feature using the base unit (feature #74 on
page 48).
0519_FPG381.book Page 76 Monday, May 19, 2003 6:46 PM
