background image

23

KX-FP701LA

6.4.

Facsimile Section

6.4.1.

Image Data Flow During Facsimile Operation

Copy (Fine, Super-Fine, Half Tone)

1. Line information is read by Contact Image Sensor (to be used as the reference white level) via route1, and is input to IC1.

Refer to 

6.4.2.Block Diagram 

(P.24)

2. In IC1, the data is adjusted to a suitable level for A/D conversion in the Analogue Signal Processing Section, and via route2 it

is input to A/D conversion (8 bit). After finishing A/D conversion, the data is input to the Image Processing Section via route3.
Then via route4 and route5, it is stored in RAM as shading data.

3. The draft’s information that is read by CIS is input to IC1 via route1. After it is adjusted to a suitable level for A/D conversion

via route2, the draft’s information is converted to A/D (8 bit), and it is input to the Image Processing Section. The other side,
the shading data which flows from RAM via route6 and route7, is input to the Image Processing Section. After finishing the
draft’s information image processing, white is regarded as "0" and black is regarded as "1". Then via routes4 and 5, they are
stored in RAM.

4. The white/black data stored as above via routes6 and8 is input to the P/S converter. The white/black data converted to serial

data in the P/S converter is input to the Thermal Head via route9 and is printed out on recording paper.

Note:

Standard: Reads 3.85 times/mm 
Fine: Reads 7.7 times/mm
Super-Fine: Reads 15.4 times/mm

Transmission

1. Same processing as 

Copy

 items 1 - 3.

2. The data stored in the RAM of IC1 is output from IC1 via routes6 and 10, and is stored in the system bus. 

Via route11, it is stored in the communication buffer inside DRAM (IC4).

3. While retrieving data stored in the communication buffer synchronous with the modem, the CPU (inside IC1) inputs the data to

the modem along route12, where it is converted to serial analogue data and forwarded over the telephone lines  via  the  NCU
Section.

Reception

1. The serial analogue image data is received over the telephone lines and input to the modem via the NCU section, where it is

demodulated to parallel digital data. Then the CPU (IC1) stores the data in the communication buffer DRAM (IC4) 

along

route12.

2. The data stored in DRAM (IC4) is decoded by the CPU (IC1) via route12, and is stored in DRAM (IC4) via routes13 and 5.
3. Same processing as 

Copy

 item 4.

Содержание KX-FP701LA
















































































































































































































Отзывы: