Panasonic KX-FP701LA страница 74 Скачать руководство пользователя

Страница: 74 / 207

KX-FP701LA

12.3. Error Messages-Report

Journal Report

If a problem occurs during fax transmission or reception, one of the following messages will be printed on the sending and jour-
nal reports.

How to output the Journal Report

1. Press

[MENU]

repeatedly until “ PRINT REPORT ” is displayed.

2. Press

[ ]

repeatedly to display “ JOURNAL REPORT ”.

3. Press

[SET]

4. The report is printed out.

Error code table:

SND=TRANSMISSION RCV=RECEPTION

Most fax communication problems can be resolved by the following steps.

1. Change the transmit level. (Service code: 596, refer to

11.1.3.Service Function Table

(P.64).)

2. Change the TX speed/RX speed. (Service code: 717/718, refer to

11.1.3.Service Function Table

(P.64).)

Note*:

If the problem remains, see the following

"Countermeasure

" flow chart.

(1) CODE

(2) RESULT

(3) MODE

SYMPTOM

Counter-

measure*

PRESSED THE STOP KEY

SND & RCV Communication was interrupted by the STOP button.

DOCUMENT JAMMED

SND

The document paper is jammed.

NO DOCUMENT

SND

No document paper.

OTHER FAX NOT RESPONDING

SND

Transmission is finished when the T0 TIMER expires.

COMMUNICATION ERROR

SND & RCV

COMMUNICATION ERROR

SND

DCN is received after DCS transmission.

COMMUNICATION ERROR

SND

FTT is received after transmission of a 2400BPS training signal.

COMMUNICATION ERROR

SND

No response after post message is transmitted three times.

COMMUNICATION ERROR

SND

RTN and PIN are received.

COMMUNICATION ERROR

RCV

No response after FTT is transmitted.

COMMUNICATION ERROR

RCV

No post message.

COMMUNICATION ERROR

RCV

RTN is transmitted.

COMMUNICATION ERROR

RCV

PIN is transmitted (to PRI-Q).

COMMUNICATION ERROR

RCV

PIN is transmitted.

OTHER FAX NOT RESPONDING

RCV

Reception is finished when the T0 TIMER expires.

ERROR-NOT YOUR UNIT

RCV

DCN is received after DIS transmission.

COMMUNICATION ERROR

RCV

DCN is received after FTT transmission.

ERROR-NOT YOUR UNIT

SND

DCN responds to the post message.

COMMUNICATION ERROR

SND

DCN is received before DIS reception.

COMMUNICATION ERROR

RCV

Reception is not EOP, EOM PIP, PIN, RTP or RTN.

COMMUNICATION ERROR

RCV

No response at the other party after MCF or CFR is transmitted.

ERROR-NOT YOUR UNIT

RCV

DCN is received after CFR transmission.

COMMUNICATION ERROR

RCV

Carrier is cut when the image signal is received.

MEMORY FULL

RCV

The document was not received due to memory full.

JUNK FAX PROH. REJECT

RCV

The fax was rejected by the junk fax prohibitor feature.

COMMUNICATION ERROR

SND & RCV Modem error. For the DCN, DCN, etc. abbreviations, refer to

6.6.Modem Section

(P.36).

Содержание KX-FP701LA
















































































































































































































Результаты поиска

Содержание KX-FP701LA

Отзывы:

Похожие инструкции для KX-FP701LA

Бренды по названию

Популярные бренды

Panasonic KX-FP701LA, Руководство по обслуживанию

Результаты поиска

Содержание KX-FP701LA

Отзывы:

Похожие инструкции для KX-FP701LA

Бренды по названию

Популярные бренды