Panasonic KX-FP701LA страница 70 Скачать руководство пользователя

Страница: 70 / 207

KX-FP701LA

11.2.3.1. Descriptions of the History Report

(1) SOFTWARE VERSION

FLASH ROM version

(2) SUM

FLASH ROM internal data calculation.

(3) YOUR LOGO

The user logo recorded in the unit. If it is not recorded,
NONE will be displayed.

(4) YOUR TELEPHONE NUMBER

The user telephone number recorded in the unit. If it is not
recorded, NONE will be displayed.

(5) FAX PAGER NUMBER

If you program a pager number into the unit, the pager
number will be displayed here.

(6) FACTORY - CUSTOMER

This shows how many days from factory production until the
user turns ON the unit.

(7) MONTH

The shows the very first month, date, year and time set by
the user after they purchased the unit.

(8) DAY

The shows the very first month, date, year and time set by
the user after they purchased the unit.

(9) YEAR

The shows the very first month, date, year and time set by
the user after they purchased the unit.

(10) TIME

The shows the very first month, date, year and time set by
the user after they purchased the unit.

(11) USAGE TIME

The amount of time the unit has been powered ON.

(12) FACTORY - NOW

This shows how many days from factory production until the
user prints out this history list.

(13) TEL MODE

The amount of time the TEL mode setting was used.

(14) FAX MODE

The amount of time the FAX mode setting was used.

(15) TEL/FAX MODE

The amount of time the TEL/FAX mode setting was used.

(16) ANS/FAX MODE

The amount of time the ANS/FAX mode setting was used.

(17) FINAL RECEIVE MODE

The last set receiving mode by the user.

(18) TONE/PULSE SELECTION

The most recently used setting used, either TONE or
PULSE.

(19) RECEIVE REDUCTION

The compression rate when receiving.

(20) SETTING NO. OF DIRECTORY

The recorded directory stations.

(21) NUMBER OF COPY

The number of pages copied.

(22) NUMBER OF RECEIVE

The number of pages received.

(23) NUMBER OF SENDING

The number of pages sent.

(24) NUMBER OF CALLER ID

The number of times Caller ID was received.

(25) NUMBER OF RECORDING MESSAGE

The number of messages recorded in TAM.

(26)~(29) Not Used
(30) NUMBER OF PRINTING WARNING LIST

The number of warning lists printed until now.

(31) NUMBER OF PRINTING HELP

The number of help lists printed until now.

(32) NUMBER OF DIVIDED PRINTING IN FAX RECEPTION

The number of faxes received that were divided into more
than one sheet since the unit was purchased.

(33) Not used
(34) FAX MODE

Means the unit received a fax message in the FAX mode.

(35) MAN RCV

Means the unit received a fax message by manual
operation.

(36) FRN RCV

Means the unit received a fax message by friendly signal
detection.

(37) VOX

Means the unit detected silence or no voice.

(38) RMT DTMF

Means the unit detected DTMF (Remote Fax activation
code) entered remotely.

(39) PAL DTMF

Means the unit detected DTMF (Remote Fax activation
code) entered by a parallel connected telephone.

(40) TURN-ON

Means the unit started to receive after 10 rings. (Remote
Turn On: Service Code #573)

(41) TIME OUT

Means the unit started to receive after Ring Time Out in
the EXT-TAM or TEL/FAX mode.

(42) IDENT

Means the unit detected Ring Detection.

(43) CNG OGM

Means the unit detected the CNG while it was sending the
Dummy Ring Back Tone in the TEL/FAX mode, or while
answering a call in the EXT-TAM mode. Or means the unit
detected the CNG while it was sending the OGM in the
ANS/FAX mode.

(44) CNG ICM

Means the unit detected the CNG while it was recording
the ICM in the ANS/FAX mode.

Содержание KX-FP701LA
















































































































































































































Результаты поиска

Содержание KX-FP701LA

Отзывы:

Похожие инструкции для KX-FP701LA

Бренды по названию

Популярные бренды

Panasonic KX-FP701LA, Руководство по обслуживанию

Результаты поиска

Содержание KX-FP701LA

Отзывы:

Похожие инструкции для KX-FP701LA

Бренды по названию

Популярные бренды