PRO2 mode setting
Bottom hold display
Incident light intensity display
Percentage display
Peak hold display
Changed intensity display (Note)
Turn OFF
Turn ON
ECO OFF
ECO ON
Note: When the differential mode ' ' or ' ' is set in PRO6 mode setting, the changed incident
light intensity is displayed.
Press
Press
Press
Turn
Turn
Turn
Turn
Press
Turn
Turn
PRO4 mode setting
Communication lock function ON
Communication lock function OFF
Back-up ON
Back-up OFF
e.g.)
When set
to ch.1
Press
Press
Press
Press
Turn
Turn
Turn
Turn
Press
Turn
Press
Turn
Turn
Cancel
Press
1CH
2CH
3CH
Press
Press
Press
Turn
Cancel
Press
Cancel
Press
e.g.)
When set
to ch.1
1CH
2CH
3CH
Press
Press
Press
Turn
PRO3 mode setting
1CH
2CH
3CH
Press
Press
Press
Press
Turn
Turn
Turn
Cancel
Press
1CH
2CH
3CH
Press
Press
Press
Turn
Cancel
Press
Hysteresis: Standard
Hysteresis: Large
Hysteresis: Small
Press
Turn
Turn
Turn
Turn
Turn
Amount of shift: 15% approx.
The amount of shift can be changed approx. 0 to 80%
(5% step).
Emission halt (Note 3)
Emitting power Hi
Emitting power Lo
Turn
Press
Press
Turn
Notes: 3)
4)
If the sensor is returned to RUN state in the
emitting halt condition, ' ' is displayed.
The ' ' goes off when the emitting power
is turned on.
Only in the response time
H-SP mode, ON
condition, the emitting power is 3 level.
PRO5 mode setting
: Confirmed
Press
㧦
Select the desired code
(Note 2)
Turn
(Blinking)
Press
Press
Press
Press
Press
Turn
Turn
(Note 1)
Adjust lock ON
Adjust lock OFF
Goes to 'RUN' mode
after blinking twice.
Interference prevention function 1
Interference prevention function 2 (Note 3)
Press
Press
Turn
Turn
Press
Turn
Press
Turn
Cancel
Press
Notes: 1)
2)
When any code other than the codes given in the Code setting table below is used, ' ' is
displayed. The factory setting is ' '.
When the code setting function is used, refer to the 'Code setting table' given below.
However, the code setting is only for the output 1.
PRO6 mode setting
Normal mode
Window
comparator
mode
Press
Press
Press
Press
Press
Press
Press
Press
Press
Rising differential mode
Trailing differential mode
Turn
Turn
Turn
Turn
Turn
Press
Press
Press
Press
Turn
Press
Normal mode
Alarm output
Error output
Note: When the differential mode is used, set the threshold value in the full-auto teaching. Furthermore, when the response
time is used in STDF mode, LONG mode or U_LG mode, use the higher threshold value than that shown below.
STDF mode: 40 digits
LONG mode: 60 digits
U_LG mode: 100 digits
ON-delay
㨯
OFF-delay
ON-delay
㨯
ONE-SHOT
ON
ON
ON-delay
㨯
OFF-delay
OFF
ON-delay
㨯
ONE-SHOT
OFF
H-02 (standard)
H-SP
H-02 (standard)
U-LG
H-02 (standard)
STDF
5s
4s
3s
2s
1s
OFF
1ms
5ms
10ms
30ms
50ms
100ms
300ms
500ms
3ms
Direct
EQFG
Direct
EQFG
Direct
EQFG
NON
OFF-delay
OFF-delay
ON-delay
ON-delay
ONE-SHOT
ONE-SHOT
ON
NON
OFF
OFF
OFF
OFF
ON
ON
ON
L-ON
L-ON
L-ON
L-ON
H-02 (standard)
H-03 (large)
H-03 (large)
H-01 (small)
digit
D-ON
D-ON
D-ON
D-ON
digit
Percent
Percent
Peak hold
Peak hold
Bottom hold
Bottom hold
STD
H-02 (standard)
LONG
H-02 (standard)
FAST
FAST
FAST
H-03 (large)
LONG
H-01 (small)
H-01 (small)
LONG
STD
STD
1st figure
2nd figure
3rd figure
4th figure
Timer
operation
Direct
EQFG
Timer
Adjust
lock
L-ON/
D-ON
Display
Response
time
H y s t e-
resis
Code setting table
3)
4)
When the interference prevention function 2 ' ' is set, the
number of mountable fibers becomes double. Furthermore,
take care that the response time also becomes double.
In order to change PRO mode setting to 'RUN' mode, press
MODE key for 2 sec. or more.
The 0-ADJ setting function in this product was removed from production starting May, 2005.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
