Panasonic FP7 CPU Unit Скачать руководство пользователя

Страница: 29 / 92

3.5 Setting of System Connection

3.5.1 List of Setting Items

System connection is used when using a programming tool via LAN port.



List of setting items

Setting item

Default

System Connection - Setting method

Operation Mode Setting

MEWTOCOL-COM

Select the operation mode MEWTOCOL-COM.

etti

ng of appl

ati

on us

Specifying use of

connection

Yes

Specify whether system connection is to be used.

MEWTOCOL

communication type

Do not connect with FP2

ET-LAN

Select "Do not connect with FP2 ET-LAN".

Open method

(server/client)

Server connection

(unspecified partner)

Select connection function settings (server

connection (unspecified partner).

Open method

(auto/manual)

Auto OPEN

Select the connection open method (auto/manual).

Select "Auto OPEN".

Communication method

TCP / IP

Select the communication protocol (TCP/IP).

Source node port No.

Connection 01: 32769
Connection 02: 32770
Connection 03: 32771
Connection 04: 32772

Specify the source node (sender) port number.

Partner node port No.

Connection 01: 32769
Connection 02: 32770
Connection 03: 32771
Connection 04: 32772

Specify the partner node (receiver) port number.

This needs not to be set if the partner node is not

specified.

Connection closing time

Connection 01: 6000
Connection 02: 360000
Connection 03: 360000
Connection 04: 360000

Setting unit:
Input the no-connection communication monitoring

time. Connection is automatically cut off when no-

connection communication exceeds the specified

time.

Partner node - Setting

method

Specification using IP

address (IPv4)

Select the setting for partner node (IP address).

This needs not to be set if the partner node is not

specified.

Partner node IP address and

name

0.0.0.0

Specify the setting for partner node (IP address /

host name). This needs not to be set if the partner

node is not specified.

3-7

Содержание FP7 CPU Unit





























































































Результаты поиска

Содержание FP7 CPU Unit

Отзывы:

Похожие инструкции для FP7 CPU Unit

Бренды по названию

Популярные бренды

Panasonic FP7 CPU Unit, Руководство пользователя

Результаты поиска

Содержание FP7 CPU Unit

Отзывы:

Похожие инструкции для FP7 CPU Unit

Бренды по названию

Популярные бренды