Panasonic FP7 CPU Unit Скачать руководство пользователя

Страница: 32 / 92

Configuration

3.6 Setting of User Connection

3.6.1 List of Setting Items



List of setting items

Setting item

Default

Setting method

Operation Mode Setting

MEWTOCOL-COM

Select an operating mode (MEWTOCOL-COM /

MEWTOCOL-COM7 / MODBUS-TCP /

MEWTOCOL-DAT / general-purpose

communication).

etti

ng of appl

ati

on us

Specifying use of

connection

Not use

Specify whether each connection is to be used.

MEWTOCOL

communication type

Conditions to be selected vary by the selected operation mode.

MEWTOCOL-DAT

MEWTOCOL-COM

is selected

Not connect to FP2

ET-LAN

Not connect to FP2 ET-LAN / Connect to FP2 ET-

LAN
When communication is to be performed with the

FP2 ET-LAN unit, select " Connect to FP2 ET-

LAN".

When selecting

general-purpose

communication

Attach a dedicated

header

Attach / Do not attach a dedicated header
When communication is to be performed with the

FP2 ET-LAN unit, select "Do not attach a dedicated

header".

Open method

(server/client)

Client connection

Select connection function settings (server

connection (unspecified partner) / server

connection (specified partner) / client connection).

Open method

(auto/manual)

Auto OPEN

Select the connection open method (auto/manual).
Select "Auto OPEN".

Communication method

TCP/IP

Select the communication protocol (TCP IP / UDP

IP).

Source node port No.

Specify the source node (sender) port number.

Partner node port No.

Specify the partner node (receiver) port number.

Unused connection closing time

Input the no-connection communication monitoring

time. Connection is automatically cut off when no-

connection communication exceeds the specified

time.

Partner node - Setting method

Specification using IP

address (IPv4)

Select the setting for partner node (IP address /

host name).

Partner node IP address and

name

0.0.0.0

Specify the setting for partner node (IP address /

host name).

KEY POINTS

•

Select a desired operation mode.

•

When client settings are used, select "Use in the connection settings" only

for the connection to be used. When "Use in the connection settings" is

selected, and if connection is failed, it is regarded as a communication error.

3-10

Содержание FP7 CPU Unit





























































































Результаты поиска

Содержание FP7 CPU Unit

Отзывы:

Похожие инструкции для FP7 CPU Unit

Бренды по названию

Популярные бренды

Panasonic FP7 CPU Unit, Руководство пользователя

Результаты поиска

Содержание FP7 CPU Unit

Отзывы:

Похожие инструкции для FP7 CPU Unit

Бренды по названию

Популярные бренды