Panasonic FP7 CPU Unit Скачать руководство пользователя

Страница: 13 / 92

1.2 Functions of LAN Port

1.2.3 User Connection



Functions of user connection

•

The FP7 CPU Unit can open virtual communication lines for up to 16 connections with

Ethernet-supporting devices connected to LAN, and send/receive data.

•

It can open multiple connections between the FP7 CPU unit and multiple nodes or a single

node, and execute communication.

•

Operation mode, open method, protocol, etc. can be selected for each connection.

IP XXXXXX

FP7 CPU

Port

8000

External

device

XXXX

Port

XXXX

Port

8001

Port

8015

Ethernet LAN

Select a desired communication

method for each connection

XXXX

Port

XXXX

Port

XXXX

FP7 CPU

Port

8000

External

device

Port

8001

Port

8015

Ethernet LAN

Select a desired communication

method for each connection

IP XXXXXX

Port

XXXX

Port

XXXX

Port

XXXX

IP XXXXXX

Note) Circled numbers in the figure above indicate examples of allocation of connection numbers.



Connection operation

•

Connection is opened from either the FP7 CPU unit side or the external device side.

•

The open method should be selected from server connection (unspecified partner), server

connection (specified partner), and client connection, in the configuration menu of FPWIN

GR7.

•

Once connection is established, communication by a user program becomes possible in

accordance with the operation mode.



Supported operation mode

Communication

port

MEWTOCOL-DAT

MEWTOCOL7-COM

MEWTOCOL-COM

MODBUS-TCP

General-

purpose

communication

Master

Slave

Master

Slave

Master

Slave

LAN port

●

○ (Note)

●

(Note) MEWTOCOL7-COM does not support master functions.

1-5

Содержание FP7 CPU Unit





























































































Результаты поиска

Содержание FP7 CPU Unit

Отзывы:

Похожие инструкции для FP7 CPU Unit

Бренды по названию

Популярные бренды

Panasonic FP7 CPU Unit, Руководство пользователя

Результаты поиска

Содержание FP7 CPU Unit

Отзывы:

Похожие инструкции для FP7 CPU Unit

Бренды по названию

Популярные бренды