Panasonic FP7 CPU Unit Скачать руководство пользователя

Страница: 10 / 92

Communication Functions of CPU Unit

1.1 Communication Ports of CPU Unit

1.1.1 Types and Purposes of Communication Ports



Communication ports of CPU unit



Functions of Ports

(1) COM1 and COM2 Ports

Attach a separately sold communication cassette to use these ports. You can select from five

types of communication cassettes.

(2) COM0 Port

This is an RS-232C port that is equipped to a standard model of CPU unit. It is equipped with

power supply terminals (5V DC and 24V DC) to which a GT series display can be connected.

(3) LAN Port

This is equipped to a standard model of CPU unit. It is used for connection to Ethernet. It can

also be connected with a programming tool. The MAC address is printed on the side of the

unit. It supports the Ethernet communication interfaces 100BASE-TX and 10BASE-T.

100BASE-TX and 10BASE-T are automatically switched by the auto negotiation function.

(4) USB Port

This is equipped to a standard model of CPU unit. This is used when connecting tool software.

REFERENCE

•

For communication using the COM port, please see the CPU Unit Users

Manual (COM Port Communication).

1-2

Содержание FP7 CPU Unit





























































































Результаты поиска

Содержание FP7 CPU Unit

Отзывы:

Похожие инструкции для FP7 CPU Unit

Бренды по названию

Популярные бренды

Panasonic FP7 CPU Unit, Руководство пользователя

Результаты поиска

Содержание FP7 CPU Unit

Отзывы:

Похожие инструкции для FP7 CPU Unit

Бренды по названию

Популярные бренды