Panasonic EverVolt EVPV HK Series страница 25 Скачать руководство пользователя

Страница: 25 / 26

General Installation Manual

ANNEX 1: INSTALLATIONS USING

MODULE LEVEL POWER

ELECTRONICS

This section is applicable to EverVolt

modules referred to in this installation

manual.

Module Level Power Electronics

(MLPE) is the name given to the

range of module-level components

that can be installed in PV system

circuits installed on or in buildings to

reduce shock hazard for emergency

responders.

From January 2019, Section 690.12

of the National Electrical Code (NEC)

(in the U.S.A.) requires the module-

level rapid shutdown of solar systems

(replacing the previous arraylevel

shutdown requirement of NEC 2014).

This means that all conductors within

an array’s in (300 mm) boundary have

to be reduced to 80 V or less within 30

seconds of rapid shutdown initiation.

MLPE devices may be used on EverVolt

modules where desirable or mandatory

(note that the certification testing of

solar modules does not include testing

with MLPE devices).

When installing an MLPE device on an

EverVolt module, follow the

instructions provided by the device

manufacturer and the instructions

specific for EverVolt modules

given below. Failure to follow the

manufacturer and the EverVolt

instructions may invalidate the

warranty.

INSTALLATION

-MLPE devices are suitable for use

wherever solar modules are suitable

for installation. Observe any limitations

set by the MLPE manufacturer. (e.g.,

minimum mounting gap between

MLPE and rooftop).

-When attaching an MLPE device to a

solar module, it must be secured to the

module frame. Follow MLPE

manufacturer instructions to ensure

optimum mounting of MLPE device

and prevent any slippage during

operation.

-MLPE devices may also be attached to

the mounting construction. In such

cases, refer to the instructions provided

by the manufacturer.

-Wherever possible, the installation of

the MLPE device should not cover the

product label on the rear of the

module.

-MLPE devices may only be installed on

EverVolt modules in the areas shown

in the diagram below (Figure 24):

• To avoid damage to the module and

to allow for thermal expansion,

there must be a minimum gap of

0.1 in (2.5 mm) between the MLPE

device and the module backsheet.

• The mounting holes in the module

frame must not be used for the

installation of MLPE devices.

• The drilling of extra holes in the

frame is not permitted and will

invalidate the module warranty.

CONNECTION

• First ensure the installation of the

MLPE device is secure and safe.

• Following the device

manufacturer’s instructions to

connect the cables from the

MLPE device to the solar module

correctly (usually positive to

positive [+ to +] and negative to

negative [- to -]).

• Connection to the next module in

the array should be done from the

‘free’ cables.

SAFETY

• Immediately disconnect the

device if there is a problem during

installation.

Figure 24. MLPE device installation zones

0 - 18.9 in [0 - 480 mm]

0 - 40 in [0 - 1016 mm]

0 - 18.9 in [0 - 480 mm]

0 - 40 in [0 - 1016mm]

Installation of MLPE device in the red

zone is not permitted.

Installation of MLPE device in the green

zone is permitted.

Содержание EverVolt EVPV HK Series



























Результаты поиска

Содержание EverVolt EVPV HK Series

Отзывы:

Похожие инструкции для EverVolt EVPV HK Series

Бренды по названию

Популярные бренды

Panasonic EverVolt EVPV HK Series, Основное руководство по установке

Результаты поиска

Содержание EverVolt EVPV HK Series

Отзывы:

Похожие инструкции для EverVolt EVPV HK Series

Бренды по названию

Популярные бренды