Panasonic EverVolt EVPV HK Series Скачать руководство пользователя

Страница: 20 / 26

General Installation Manual

MOUNTING METHODS:

MOUNTING HOLES

EverVolt modules can be installed

utilizing the four mounting holes 0.4 x

0.25 in (11 x 6.6 mm) on the underside

of the module [Figure 18 & 19] in

conjunction with a device, e.g., screws,

lockbolts or structural blind fasteners,

with specifications suitable for the

installation (Figure 20).

Installing the EverVolt modules using

the mounting holes has been found to

comply with UL 61730 requirements

for downward pressure,e.g., snow, of

up to 5400 Pa (3600 Pa design load*)

and upward pressure,e.g., wind, of

up to 2400 Pa (1600 Pa design load*)

according to the following instructions

(*design loads apply a safety factor of

1.5 to the stated test load, e.g., test

load 5400 Pa / 1.5 = 3600 Pa design

load).

The product warranty will be voided if

additional holes are made in the frame.

All fixing and fastening materials must

be corrosion resistant.

When installing using mounting holes,

the frame and module edge of each

module must be supported by two rails

of aluminium or galvanized steel

suitable for the application and

appropriate for the local environment.

Observe the following procedures when

using mounting

holes:

• The mounting construction must be

of a corrosion resistant material,

e.g., aluminum or galvanized

steel, and appropriate for the local

environment.

• All four mounting holes in the

frame must be used (Figure 21).

• Additional electrical bonding to

Ground is required for the support

structure,

• Refer to the fixing device

manufacturer’s installation

instructions for preload or torque

values.

• Do not contact a tip of a mounting

bolt to back sheet of the module

when fixing the module to the

mounting structure rail.

• EverVolt modules must be secured

with a torque between 8.8-18.4 ft-

lb (12 - 25 Nm ).

• Module should be attached on a

mount or support structure rail by

corrosive-resistant metal clamps.

• Appropriate material should be

used for mounting hardware (the

module frame, mounting structure,

and hardware) to prevent itself

from corrosion.

• Panasonic does not provide a

warranty for clamps. The module

warranty Panasonic provides shall

be voided if clamps selected by

the customer are of an improper

material or size.

• Please contact your Panasonic

Authorized Representative with

questions regarding mounting

profiles for modules if needed.

Figure 18. Mounting holes_EVPVxxx, EVPVxxxK ,

EVPVxxxPK Series modules

Part Name

Specification

Material

Rail

6105 - T5 aluminum extrusion

Bolt

1/4” x 20 - 5/8”

ASTM F593 (stainless steel)

Nut

1/4” x 20

ASTM F593 (stainless steel)

Figure 21. Mountinghole installation example

Figure 20. Device specifications for Mounting holes

Figure 19. Mounting holes_EVPVxxxH Series modules

Scale:

1:1.57

0.43 in

±0.008

[11 mm

±0.2

]

0.26 in

±0.008

[6.6 mm

±0.2

]

0.81 in

±0.02

[20.5 mm

±0.5

]

17.9 in [455 mm]

Scale:

1:1.57

0.43 in

±0.008

[11 mm

±0.2

]

0.26 in

±0.008

[6.6 mm

±0.2

]

0.81 in

±0.02

[20.5 mm

±0.5

]

18.1 in [460 mm]

Содержание EverVolt EVPV HK Series



























Результаты поиска

Содержание EverVolt EVPV HK Series

Отзывы:

Похожие инструкции для EverVolt EVPV HK Series

Бренды по названию

Популярные бренды

Panasonic EverVolt EVPV HK Series, Основное руководство по установке

Результаты поиска

Содержание EverVolt EVPV HK Series

Отзывы:

Похожие инструкции для EverVolt EVPV HK Series

Бренды по названию

Популярные бренды