Panasonic EverVolt EVPV HK Series страница 10 Скачать руководство пользователя

Страница: 10 / 26

General Installation Manual

MODULE INSTALLATION

EverVolt modules are designed for

capturing solar radiation and can be

installed where they conform to all

local structural regulations. If installing

EverVolt modules in overhead or

vertical constructions, the installer

must ensure that all local building

codes and regulations specific to such

installations are correctly followed. The

IP rating of the junction box provides a

level of protection that allows modules

to be mounted in any orientation.

There are different options for

securing EverVolt modules depending

on the design of the array. Mounting

hardware is not supplied by Panasonic.

Ensure the mounting structure can

withstand anticipated wind and snow

loads. Follow the mounting hardware

manufacturer’s instructions and

recommendations at all times.

• Install modules where they are not

shaded by obstacles like buildings

or trees. Especially pay attention to

avoid partially shading the modules

by objects during the daytime. If

a part of the PV module is always

shaded, hot spot may occur and the

PV module may break down.

• Water stains might be caused

when rain water remains on the

glass surface for a long time. To

avoid water stains, Panasonic

recommends to install modules

at a slope steeper than the water

gradient.

• Modules should be firmly fixed

in place in a manner suitable to

withstand all expected loads,

including wind and snow loads.

• Metals used in locations that are

exposed to moisture shall not be

employed alone or in combinations

that could result in deterioration or

corrosion.

USE OF RAILS AND CLAMPS

Installing the EverVolt modules with

clamps and rails has been found to

comply with UL 61730 requirements

for downward pressure, e.g., snow, of

up to 7000 Pa (4666 Pa design load*)

and upward pressure, e.g., wind, of

up to 4000 Pa (2666 Pa design load*)

according to the following instructions

(*design loads apply a safety factor of

1.5 to the stated test load, e.g., test

load 7000 Pa / 1.5 = 4666 Pa design

load).

When installing on mounting rails,

ensure they run underneath the

module and provide support to the

frame. The positioning of the rail must

ensure that the minimum clamp grip

length and the central point of the

fixation, e.g., the bolt, is fully within the

required clamping zone as indicated on

the following pages.

EverVolt modules must be secured

with a torque between 8.8-18.4 ft-

lb (12 - 25 Nm). Clamp installation

must be carried out according to

the manufacturer’s instructions,

including specific hardware and torque

requirements. Ensure the clamps used

are suitable for the planned installation

and expected system design loads.

• The grip area must not extend onto

the module glass and/or cause cell

shading.

• Avoid the application of excessive

pressure to prevent frame

deformation.

• The module must be secured, e.g.,

clamped, at least once in each

of the four marked zones shown

below (Figure. 8).

Figure 7. Clamp specifications

Specifications

Length

Grip depth

0.2 - 0.4in (5-10mm)

Min. grip length

1.6in (40mm)

Torque

See manufacturer’s

instructions

Figure 8. Module quarter division

Min. grip length:
1.6 in (40 mm)

Grip depth:
0.2 - 0.4 in (5 - 10 mm)

Содержание EverVolt EVPV HK Series



























Результаты поиска

Содержание EverVolt EVPV HK Series

Отзывы:

Похожие инструкции для EverVolt EVPV HK Series

Бренды по названию

Популярные бренды

Panasonic EverVolt EVPV HK Series, Основное руководство по установке

Результаты поиска

Содержание EverVolt EVPV HK Series

Отзывы:

Похожие инструкции для EverVolt EVPV HK Series

Бренды по названию

Популярные бренды