VQT2J51
67
DVB Auto Setup by Signal Quality
DVB Auto Setup by Region
You can restart auto channel setting for digital terrestrial channels if
the setup (
>
13) fails for some reason.
If you want to set the channel list best suited to your region, select
“DVB Auto Setup by Region”. Follow the on-screen instructions to
select the region you live in.
However, if you perform “DVB Auto Setup by Signal Quality” or “DVB
Auto Setup by Region”, all channel settings, Favourites and all the
timer recording programmes are deleted. (All the settings except for
the ratings level, ratings PIN, Owner ID, Clock and remote control
code, etc. return to the factory preset.)
When the confirmation screen appears
Press [
2
] to select “Yes”, then press [OK].
Tips
≥
You can also use the following method to restart DVB Auto Setup
by Signal Quality.
When the unit is turned on and stopped, press and hold [CH
W
]
and [
X
CH] on the main unit simultaneously for about 5 seconds.
– Auto-Setup screen appears.
DVB Manual Tuning
You can set channels manually if the “DVB Auto Setup by Signal
Quality” could not be completed successfully.
1 Press [
3
,
4
] to select the channel you want to set.
– Select the channel by checking the signal strength and signal
quality displays. [Refer to “Signal Condition” (
>
right) for signal
strength and signal quality.]
2 Press [OK] to start scan.
The set channel is displayed in
the table.
≥
Repeat steps 1–2 to tune
other channels.
3 Press [EXIT], then press [
W X
CH] to check that applicable
channels have been selected.
Add New DVB Channels
You can search for newly added digital terrestrial channels to
receive.
– The unit starts searching for newly available digital terrestrial
channels. This takes about 5 minutes.
– The bar over the table shows you the search progress. At the
end of the search, the number of found new digital stations
appears.
– “No new DVB channels found.” is displayed when no new
channels can be found.
Press [OK] to save the newly found channels.
Tips
To cancel in middle
Press [RETURN ].
The channels found before stopping are not saved.
Setup
Disc
Picture
Sound
Display
Connection
Tuning
Others
OK
RETURN
TAB
SELECT
VHS
Favourites Edit
DVB Auto Setup by Signal Quality
DVB Manual Tuning
Add New DVB Channels
DVB Preferred Multi Audio
DVB Preferred Subtitles
English
English
DVB Auto Setup by Region
Signal Condition
DVB Manual Tuning
RETURN
START SCAN
CH
Frequency
MHz
No.
New
Channel Name
Type
0
10
0
10
[CH54]
738.0
Signal Quality
Signal Strength
TV: 0 Radio: 0 Data: 0
DVB Manual Tuning
RETURN
START SCAN
CH
Frequency
MHz
No.
New
Channel Name
Type
0
10
0
10
[CH54]
738,0
Signal Quality
Signal Strength
TV: 15 Radio: 4 Data: 0
8 DVB channels found.
BBC ONE Wales
BBC 2W
BBC NEWS 24
BBC Radio Wales
ITV
1
2
3
4
5
TV
TV
TV
Radio
TV
-
-
-
-
-
Setup
Disc
Picture
Sound
Display
Connection
Tuning
Others
OK
RETURN
TAB
SELECT
VHS
Favourites Edit
DVB Auto Setup by Signal Quality
DVB Manual Tuning
Add New DVB Channels
DVB Preferred Multi Audio
DVB Preferred Subtitles
English
English
DVB Auto Setup by Region
Signal Condition
Add New DVB Channels
RETURN
Scan
CH 21
68
Channel Name
Searching...
CH
Type
Quality
TV: 15 Radio: 4 Data: 0
BBC ONE Wales
27
TV
9
BBC 2W
27
TV
9
BBC NEWS 24
27
TV
9
BBC Radio Wales
27
Radio
9
Signal Condition
You can check the quality and strength of digital broadcast signals.
When “Signal Condition” is displayed in grey and cannot be
selected:
1
Press [EXIT] to exit the screen.
2
Press [
W X
CH] to select a digital channel. “D” appears on the
unit’s display.
3
Display the Setup menu again.
The quality and strength of the signal are shown.
Press [
W X
CH] to select the channel.
Signal Quality
Below 2 (display red)
The signal quality is so poor that there
may be interference in the pictures and
sound.
2–5 (display orange)
The signal quality is basically adequate,
but brief interference in the pictures and
sound is possible in isolated case.
Over 5 (display green)
Optimum picture and sound quality.
Signal Strength
The display for signal strength is grey. “0” means signal strength 0%,
“10” means signal strength 100%.
≥
If the signal is too strong, the display will change from grey to red.
Reduce the signal amplification at your aerial.
≥
When the signal is weak:
– check that the aerial is correctly positioned.
– adjust the aerial reception with “DVB Manual Tuning” in the Setup
menu (
>
left).
– check that the current digital broadcast channel is correctly
broadcasting.
– check that your aerial is capable of receiving DVB broadcasts.
DVB Preferred Multi Audio
Choose the audio language for digital broadcast.
If the selected language is not available, then the original language
will be selected.
[English]
[Welsh]
[Gaelic]
DVB Preferred Subtitles
Choose the subtitle language for digital broadcast.
If the selected language is not available, then the original language
will be selected.
[English]
[Welsh]
[Gaelic]
[English for hearing impaired]
[Welsh for hearing impaired]
[Gaelic for hearing impaired]
Setup
Disc
Picture
Sound
Display
Connection
Tuning
Others
OK
RETURN
TAB
SELECT
10
10
VHS
Favourites Edit
DVB Auto Setup by Signal Quality
DVB Manual Tuning
Add New DVB Channels
DVB Preferred Multi Audio
DVB Preferred Subtitles
English
English
DVB Auto Setup by Region
Signal Condition
Signal Quality
0
Signal Strength
0
RETURN
C
Channel –
[CH54] 20 BBC ONE Wales
DVB Channel
DVB Signal Condition
10
10
DMR-EZ49VEB_VQT2J51.book 67 ページ ２００９年１２月２１日 月曜日 午後５時４０分
