VQT2J51
13
STEP 3
Setting the Channels and Clock
Preparation:
≥
Turn on the mains for the television
(and connected equipment) and
select the appropriate AV input to suit
the connections to this unit.
≥
These are the first settings you make
upon buying the unit. You don’t need
to make these settings again.
1
to turn the unit on.
DVB Auto Setup starts. The unit
will search for the digital terrestrial
channels. This takes about
5 minutes.
2
Power Save in Standby
Function:
3
,
4
to select “On”,
“On Timer” or “Off”, then
“On”:
It will go into the Power Save in Standby mode
when the unit is in standby mode.
“On Timer”: Press [
3
,
4
,
2
,
1
] to set the start and stop time,
then press [OK].
“Off”:
It is possible to start quickly from the standby
mode. (Quick Start mode)
≥
“Power Save in Standby” is set to activate during
the setting time period.
– The features of the Power Save in Standby function when
the unit is in standby mode are as below.
§
1
The unit could take over 1 minute to switch ON from standby mode with
Quick start deactivated.
This time could be reduced to less than 10 seconds with Quick start
activated.
§
2
When “RF OUT ( Aerial Signal )” is set to “Off” in the Setup menu (
>
72)
3
When setup has completed, the confirmation screen appears.
(continued on the next page)
TV
TIME SLIP
TEXT
STTL
DISPLAY
DIRECT TV REC
EXT LINK
REC MODE
REC
-10s
MANUAL SKIP
+60s
STOP
PAUSE
PLAY
INPUT
SELECT
0
9
8
7
6
5
4
3
2
1
CH
CH
TRACKING/V-LOCK/PAGE
CHAPTER
PROG/CHECK
SKIP/INDEX
REW
JET REW
FF
SLOW/SEARCH
RESET
VOL
AV
DRIVE
SELECT
STATUS
EXIT
OPTION
RETURN
DELETE
OK
DIR
EC
T N
AV
IGA
TO
R
FUN
CTIO
N M
EN
U
GUIDE
Tips
To cancel Auto-Setup
Press [RETURN ].
If the unit displays “No stations
found!”
Press [
1
] to select “No” and press [OK].
Go to step
2
. After you have performed
steps
2
–
;
, turn off the unit and confirm
the cable or aerial input is connected to
the RF IN terminal. Restart the Auto-
Setup again (
>
67, DVB Auto Setup by
Signal Quality).
If the clock setting menu appears or
the clock is not correct
Set the clock manually (
>
14).
Restarting the Auto-Setup (
>
67, DVB
Auto Setup by Signal Quality)
To set the channel list best suited to
your region (
>
67, DVB Auto Setup by
Region)
About the screen saver function
When this unit is not operated for
approximately 5 minutes while the screen
is being displayed, the screen saver may
be displayed.
You can turn this function off (
>
69,
Screen Saver).
TV’s remote
control
DVB Auto Setup
Scan
CH 21
68
Channel Name
RETURN
Searching...
BBC ONE Wales
BBC 2W
CH
27
27
Type
TV
TV
Quality
9
9
BBC NEWS 24
27
TV
9
BBC Radio Wales
27
Radio
9
TV: 6 Radio: 4 Data: 0
Power Save in Standby
On
To
OK
RETURN
CHANGE
:00
From
:00
Saves standby power consumption
by disabling Quick Start function and
AV2 loop-through in standby.
Power Save
0
6
OK
Power Save in Standby
Power consumption
Quick Start*
1
Front display
Activated (On
/ On Timer)
Deactivated
(Off)
Approx. 0.5W
*
2
Approx. 14W
Stays lit
Deactivated
Activated
Cannot do
Can do
Watching the picture from the
digital satellite receiver
connected to the AV2 terminal
Turns off
(The clock display
disappears.)
OK
DMR-EZ49VEB_VQT2J51.book 13 ページ ２００９年１２月２１日 月曜日 午後５時４０分
