Panasonic CU-B14DBE5 Скачать руководство пользователя страница 89

Страница: 89 / 109

12.5. Self-diagnosis error code table

• The display screen on the wired remote control unit and the self-diagnosis LEDs (green) on the outdoor unit printed circuit board

in the outdoor unit can be used to indicate where the location of a problem is.
Refer to the table below to remove the cause of the problem, and then re-start the air conditioner system.

• If the problem disappears and operation returns to normal, the CHECK display on the remote control unit will switch off, but the

self-diagnosis LED will remain illuminated until operation is resumed. ... illuminated.

Wired remote

control unit display

Outdoor unit printed circuit board

LED

Location or problem

Check location

Abnormal

dispaly

Detail

dispaly

F15

-01

Drain level Float switch problem Drain pump and drain pipe, indoor unit con-

nectors

F16

-01

Louver switch problem

Louver motor, decorative panel connection
terminal, or indoor unit louver motor connec-
tors

F17

-02

D.C. Fan motor problem

Indoor unit D.C.Fan motor or connection ter-
minals

F20

-01

Indoor temperature sensor prob-
lem

Indoor temperature sensor lead wire or indoor
unit connector

-02

Remote control thermistor prob-
lem

Remote control thermistor

F21

-01

Pipe temp. sensor problem
(indoor unit)

Pipe temperature sensor lead wire or indoor
unit connector

F26

-01

Remote control transmission
problem

Remote control unit cable and connection ter-
minals

F27

-01

Indoor/outdoor unit disconnec-
tion problem

Indoor/outdoor unit connection cable and
connection terminals, or indoor unit power
supplies (indoor side)

-05

Indoor/outdoor unit connection
error problem

Indoor/outdoor unit connection wire (indoor
side)

-01

Indoor/outdoor unit disconnec-
tion problem

Indoor/outdoor unit connection cable and
connection terminals, or outdoor unit power
supplies (outdoor side)

-05

Indoor/outdoor unit connection
error problem

Indoor/outdoor unit connection wire (outdoor
side)

F30

-01

System problem

Total capacity for the number of indoor units is
insufficient, or over. Check the total capacity
and the number of indoor units

-02

Open phase, or reversed phase
of supply

Check the main power supply terminal board
connections, or switch over any two of the
power supply wires.

F31

-01

Suction pressure protection

Insufficient refrigerant or valve operation
(closed)

-02

High-pressure cut-off

Check the Refrigeration system

-06

4 way valve problem

Check the 4 way valve or lead wire

-10

Refrigerant system problem

Valve operation (closed), or refrigerant sys-
tem

F32

-05

Compressor overcurrent protec-
tion

Open phase or lock in compressor

-06

Compressor discharge temp.
protection

Insufficient refrigerant

F40

-21

Outdoor heat exchanger outlet
temperature sensor problem

Outdoor heat exchanger outlet temperature
sensor (COND TEMP) lead wire, connector

-51

Compressor discharge tempera-
ture sensor problem

Compressor discharge temperature sensor
(DIS T. TEMP) lead wire, connector

F41

-02

High pressure switch open circuit
problem

High-pressure switch lead wire, connector

-12

Low pressure sensor problem

Low pressure sensor lead wire, connector or
valve operation (closed)

Содержание CU-B14DBE5














































































































Результаты поиска

Содержание CU-B14DBE5

Отзывы:

Бренды по названию

Популярные бренды

Panasonic CU-B14DBE5, Руководство по обслуживанию

Результаты поиска

Содержание CU-B14DBE5

Отзывы:

Бренды по названию

Популярные бренды