manualshive.com logo in svg

Panasonic CU-B14DBE5, Руководство по обслуживанию

Поделиться
Скачать
Panasonic CU-B14DBE5 Скачать руководство пользователя страница 62

62

10.7. Wireless remote control installation manual

Wireless Remote Control Installation Manual

• Before installing the wireless remote controller, be sure to thoroughly read the “Notes with regard to safety” section of the instal-

lation manual provided with the indoor unit.

• After installing the wireless remote controller, carry out a test operation to check that the remote controller functions properly, and

also explain the operation and cleaning procedures to the customer in accordance with the details in the instruction manual.
Furthermore, ask the customer to keep this installation manual and the instruction manual in a safe place for later reference.

10.7.1.

Accessories supplied with the wireless remote controller

10.7.2.

Points and notes regarding wireless remote controller setting-up location

• The wireless remote controller can be used to operate indoor units at a maximum range of 8 metres from directly facing infront of

the indoor unit.

• If the remote controller is at an angle to the receptor unit, the operation range may become shortened.
• The accessory receptor unit must be attached to the veneer panel.
• The receptor unit for the wireless remote controller should be in a place where it will not be affected by direct light from fluores-

cent lights. (Refer to the illustration below.)
(If using an inverter-type fluorescent light, keep the receptor unit at least 1m away from the light, otherwise remote control oper-
ation may not work properly.)

• If installing in a place where a power supply is generating electromagnetic noise, take measures such as installing a noise filter.
• Install at least 3m away from any noise sources, and shield the electric cables using an iron conduit pipe.
• Install at least 1m away from equipment such as TVs and radios. (Otherwise picture distortion or static may occur.)

No.

Name

Q’ty

Cassette

Ceiling

1.

Wireless Remote Controller

1

1

2.

R03 battery

2

2

3.

Holder (For securing remote controller)

1

1

4.

Holder fixing screw

2

2

5.

Receptor unit (For Cassette Type)

1

-

6.

Receptor unit (For Ceiling Type)

-

1

7.

Installation manual

1

1

Содержание CU-B14DBE5














































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды