Panasonic CS-VE9NKE Скачать руководство пользователя страница 104

Страница: 104 / 140

104

16.1.8 Removing the Air Filter Frame (Auto Cleaner)

1 Perform “16.1.1 Removing the Front Panel”.
2 Perform “16.1.2 Removing the Air Filters”.



Note on disassembly: The air filter frame can be removed without removing the air filters. Nevertheless, be

sure to remove the air filters because the top portion of the air filters may get stuck while reattaching the
air filter frame.

3 Perform “16.1.3 Removing the Front Grille (Right) and Front Grille (Left)”.
4 Perform “16.1.4 Removing the Control Board Box”.



Note on disassembly: There is no need to remove the control board box. However, the air filter frame

cannot be removed unless all the engaged connectors are disconnected and the terminal plate is moved a
little bit.

5 Remove 4 screws (2 screws each on the right and left sides) which fix the air filter frame (auto cleaner).

Содержание CS-VE9NKE













































































































































Результаты поиска

Содержание CS-VE9NKE

Отзывы:

Бренды по названию

Популярные бренды

Panasonic CS-VE9NKE, Руководство по обслуживанию

Результаты поиска

Содержание CS-VE9NKE

Отзывы:

Бренды по названию

Популярные бренды