manualshive.com logo in svg

Panasonic CS-A28BKP5, Руководство по обслуживанию

Поделиться
Скачать
Panasonic CS-A28BKP5 Скачать руководство пользователя страница 43

1.

Grounding is necessary. It may cause electrical shock if grounding is not perfect.

2.

Do not install the unit at place where leakage of flammable gas may occur. In case gas leaks and accumulates at
surrounding of the unit, it may cause fire.

3.

Carry out drainage piping as mentioned in installation instructions. If drainage is not perfect, water may enter the room and damage the
furniture.

1.

Selection of the installation location.
Select a installation location which is rigid and strong enough to support or hold the unit, and select a location for easy maintenance.

2.

Power supply connection to the room air conditioner.
Connect the power supply cord of the room air conditioner to the mains using one of the following method.
Power supply point shall be the place where there is ease for access for the power disconnection in case of emergency.In some
countries, permanent connection of this room air conditioner to the power supply is prohibited.
 1. Power supply connection to the receptacle using a power plug. Use an approved 20A power plug with earth pin for the connection to

the receptacle.

 2. Power supply connection to a circuit breaker for the permanent connection. Use an approved  circuit breaker as shown in the table

below for  the permanent connection. It must be a double pole switch with a minimum 3 mm contact gap.

3.

Do not release refrigerant.
Do not release refrigerant during piping work for installation, re-installation and during repairing a refrigeration parts. Take care of the
liquid refrigerant, it may cause frostbite.

4.

Installation work.
It may need two people to carry out the installation work.

5.

Do not install this appliance in a laundry room or other location where water may drip from the ceiling, etc.

43

CS-A28

BKP5/CU-A28BKP5

Circuit Breaker

CS/CU-W28BKP5

CS/CU-A28BKP5

30 A

20 A

Содержание CS-A28BKP5














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды