Panasonic AWPH360N - PAN/TILT HEAD Скачать руководство пользователя | Manualshive

Страница: 14 / 52

background image

- 14 -

Installation

(The installation work must be performed by your dealer without fail.)

$

Mounting the camera

The pan/tilt head’s camera mounting section has a mechanism for maintaining the
camera’s balance that moves the camera mounting plate using a guide roller as a fulcrum.
Use the described recommended lenses corresponding to the camera to be used.
(Before mounting a lens other than recommended lenses, consult with your dealer.)

1. Change the position of guide pin

A

and/or the camera mounting screws in accordance

with the following installation of the pan/tilt head before mounting the camera.

2. Adjust the balance by loosening the guide screws and moving the camera mounting plate.
3. Upon confirming the position where the balance is maintained, firmly tighten the guide

screws. If the balance cannot be maintained, change the position of guide pin

B

or the

positions of the guide screws, and adjust the balance again.

<Note>

O

The guide roller is fixed in place. Do not remove the guide roller screw.

Camera mounting plate

Camera mounting screws

Guide screw

Guide roller

Guide screw

Guide pin

B

Guide pin

A

Camera mounting plate

Camera mounting
screws

Guide screw

Guide roller

Guide screw

Guide pin

B

Guide pin

A

<Stand-alone installation>

<Suspended installation>

Change the position of the camera mounting
screws and the guide pin

A

to change the

installation.

«
...
12
13
14
15
16
...
»

Содержание AWPH360N - PAN/TILT HEAD





















































Отзывы:

Нет отзывов

Похожие инструкции для AWPH360N - PAN/TILT HEAD

Бренд: Park Play Страницы: 18

Бренд: Zell Страницы: 33

DS1-MP10RX series

Бренд: NEC Страницы: 39

Бренд: Easy@Home Страницы: 28

Бренд: KDS Страницы: 72

Wormhole Station JUH-320

Бренд: J5create Страницы: 24

Бренд: LAUMAS Страницы: 44

Бренд: Paradox Страницы: 2

Бренд: Fabbri Страницы: 4

Merrytec MK054V RC Series

Бренд: V-TAC Страницы: 105

Бренд: Burley Страницы: 16

Бренд: Spector&Co Страницы: 9

Бренд: Minwax Страницы: 7

TOURNEY REAR DRIVE SYSTEM - TECHNICAL

Бренд: Shimano Страницы: 2

Бренд: XD COLLECTION Страницы: 20

Бренд: Kerbl Страницы: 2

Бренд: SWEEX Страницы: 1

Бренд: Anslut Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды