Panasonic AJ-D400 Скачать руководство пользователя страница 33

Страница: 33 / 104

2-16

3-8. Tension Confirmation

SPEC

PLAY :

59mN ± 10mN (6gf ± 1gf)

REV :

88mN ± 20mN (9gf ± 2gf)

MODE

PLAY, REV

TAPE

63 min M size blank tape
123min. L size blank tape (AJ-D200,
AJ-D210, AJ-D215)

TOOL

VFK1145 (Tension Meter)

♦

Please confirm that the calibration of Tension
Meter before measurement of tension value follow
below procedure.

<Calibration of Tension Meter>
1. Connect the 7 grams calibration weight to

DVCPRO tape. (It tape and weight are included to
VFK1145.)

2. Set the above tape to the Tension Meter as

shown in figure 3-8-1.

3. Pull up the tape as speed 33mm/sec and adjust

the Tension Meter so that the meter shows 7
grams.

♦

With tape pass direction should be the same
direction of tape transportation under the VTR,
when confirm the Tension Meter as shown in figure
3-8-1.

Figure 3-8-1

1. Play back beginning portion of the tape.
2. Insert the tension meter to between S3 post and

S4 post as shown in figure 3-8-2.

3. Confirm that the tension value is within

specification.

Figure 3-8-2

4. Place the unit in REV mode.
5. Insert the tension meter to between S4 post and

S5 post as shown in figure 3-8-3.

6. Confirm that the tension value is within

specification. (Read the meter display from rear
side as shown in figure 3-8-3.)

7. If it out of specification, please perform the

Tension Arm Adjustment.

Figure 3-8-3

NOTE :
Be careful not to give some tape damage.

Содержание AJ-D400









































































































Результаты поиска

Содержание AJ-D400

Отзывы:

Похожие инструкции для AJ-D400

Бренды по названию

Популярные бренды

Panasonic AJ-D400, Руководство по обслуживанию

Результаты поиска

Содержание AJ-D400

Отзывы:

Похожие инструкции для AJ-D400

Бренды по названию

Популярные бренды