Panasonic AJ-D400 Скачать руководство пользователя страница 95

Страница: 95 / 104

3-20

(Installation)
1. Remove the Shield Case from the New A/C Head

and solder the lead wires to New A/C Head.
(Refer to Figure 1-23-3)

2. Reinstall the shield case to A/C Head.
3. Install the A/C Head to A/C Head Plate by tight 2

screws (A), then set to parallel the gap between
A/C Head and A/C Head Plate.

4. Install the A/C Head Unit.
5. Hang on the Head Height Adjustment Spring and

tighten the Nut (C).

6. Clean the surface of the A/C Head.

Figure 1-23-3

A/C Head

Cable Color

Connector

Pink

Yellow

White

Pink

Red

White

Pink

Green

White

Yellow

P30

Black

<A/C Head Adjustment>

1. After change the A/C Head, please perform the

following steps.

NOTE :
PG Shifter and CUE AUDIO adjustment procedures
are mentioned on Electrical Adjustment Procedures
on Service Manual.

START

3-14. A/C Head Tilt Adjustment

NOTE : PG Shifter Adjustment

3-18. A/C Head Azimuth & X-value Adjustment

3-15. A/C Head Height Adjustment

END

3-29. to 3-33. LISTA Adjustment

NOTE : CUE AUDIO Adjustment

3-34. Self Rec/Play Envelope

Waveform Confirmation

Содержание AJ-D400









































































































Результаты поиска

Содержание AJ-D400

Отзывы:

Похожие инструкции для AJ-D400

Бренды по названию

Популярные бренды

Panasonic AJ-D400, Руководство по обслуживанию

Результаты поиска

Содержание AJ-D400

Отзывы:

Похожие инструкции для AJ-D400

Бренды по названию

Популярные бренды