Panasonic AFP7PSA1 Скачать руководство пользователя страница 84

Страница: 84 / 109

8-8

Specifications

8.1.4 Operation Memory Area

Name

Usable devices and ranges

Functions

External input

8,192 points (X0 to X511F) (Note 1)

Turns on or off based on external input.

External
output

8,192 points (Y0 to Y511F) (Note 1)

Externally outputs on or off state.

Internal relay

32,768 points (R0 to R2047F) (Note 2)

Relay which turns on or off only within
program.

Link relay

16,384 points (L0 to L1023F) (Note 2)

This relay is a shared relay used for PLC
link.

Timer

4,096 points (T0 to T4095) (Note 2)

This goes on when the timer reaches the
specified time.

Counter

1,024 points(C0 to C1023) (Note 2)

This goes on when the timer increments.

System relay

Approx. 1120 points
(approx. 70 words)

Relay which turns on or off based on
specific conditions and is used as a flag.

Pulse relay

4,096 points (P0 to P255F)

This relay only turns on during one scan at
the start of the execution condition.

Error alarm
relay

4,096 points (E0 to E4095)

This relay ensures that error conditions
that are freely allocated by the user are
memorized in the memory.

Direct input

Can allocate input numbers to each
slot (IN0 to IN62F) (Note 3)

1-bit device

Direct output

Can allocate output numbers to each
slot (OT0 to OT62F) (Note 3)

This relay is for input/output processing
during operation, without depending on
usual I/O refresh.

External input

(Note1)

WX0 to WX511 (Note 1)

Code for specifying 16 external input
points as one word (16 bits) of data.

External
output

(Note1)

WY0 to WY511 (Note 1)

Code for specifying 16 external output
points as one word (16 bits) of data.

Internal relay

WR0 to WR2047 (Note 2)

Code for specifying 16 internal relay points
as one word (16 bits) of data.

Link relay

ｂ

0 to WL1023

Code for specifying 16 link relay points as
one word (16 bits) of data.

Data register

Max. DT 999424 words
(DT0 – DT999423) (Note 2) (Note 4)

Data memory used in program.
Data is handled in 16-bit units (one word).

Link register

16,384 words (LD0 to LD16383)
(Note 2)

This is a shared data memory which is
used within the PLC link. Data is handled
in 16-bit units (one word).

Unit memory

Max. 512K words per unit (Note 3)

This device is for accessing the unit
memory of intelligent units. Its size varies
by unit, and is allocated by default.

16-bit device

System data
register

Approx. 110 words

Data memory for storing specific data.
Various settings and error codes are
stored.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание AFP7PSA1














































































































Результаты поиска

Содержание AFP7PSA1

Отзывы:

Похожие инструкции для AFP7PSA1

Бренды по названию

Популярные бренды

Panasonic AFP7PSA1, Руководство пользователя

Результаты поиска

Содержание AFP7PSA1

Отзывы:

Похожие инструкции для AFP7PSA1

Бренды по названию

Популярные бренды