Panasonic AFP7PSA1 Скачать руководство пользователя страница 40

Страница: 40 / 109

4-8

Installation

and Wiring

4.2 Wiring the Power Supply

4.2.1 Common Precautions



To avoid the influence of noises



Use a low noise power supply.



The inherent noise resistance is sufficient for the noise superimposed on the power wires,

however, the noise can be attenuated further by using the isolation transformer.



Also, twist the power supply cables to minimize adverse effects from noise.



Keep the power supply wiring separate

Wiring to the CPU unit, input devices, and power equipment should have separate wiring
systems.



Measures regarding power supply sequence (start up sequence)



Have the power supply se

quence such that the power supply of PLC turns off before

the power supply for input and output.



If the input/output power supplies are turned off before the power PLC, the CPU unit will

detect the input fluctuations and may begin an unscheduled operation.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание AFP7PSA1














































































































Результаты поиска

Содержание AFP7PSA1

Отзывы:

Похожие инструкции для AFP7PSA1

Бренды по названию

Популярные бренды

Panasonic AFP7PSA1, Руководство пользователя

Результаты поиска

Содержание AFP7PSA1

Отзывы:

Похожие инструкции для AFP7PSA1

Бренды по названию

Популярные бренды