Panasonic AFP7PSA1 Скачать руководство пользователя страница 42

Страница: 42 / 109

4-10

Installation

and Wiring

4.2.3 Wiring for the Power Supply Part of the CPU Unit



When the CPU unit is used with 24V DC power supply, perform wiring for power supply as

follows.



Use the power supply cables (Part No.:AFPG805) that come with the unit to connect the

power supply.
Brown: 24V DC, Blue: 0V, Green: functional earth



Power supply part of the CPU unit

Blue: 0V

Brown: +24V

Green: Function earth

External power supply

Fed from an external power supply 24V DC

Power supply cable (attached)

Power supply connector



Power supply voltage



Confirm that the power supply voltage is within the allowable range of the power supply.

Rated input

voltage

Allowable

voltage range

Rated output

capacity

24V DC

20.4 to 28.8 V DC

At least 24 W



When a programmable display GT series is connected to the GT power supply terminal

(24V) of the CPU unit, use it within the range of 21.6 to 26.4 V DC.



Selection of a power supply



Referring to Section 1.2, select a power supply larger than the capacity of the unit.

In the minimum configuration, select a power supply of 24 W or larger.



In order to protect the unit against abnormal voltage from the power supply line, the power

supply should be an insulated type, and should be enclosed within a protective circuit. The
regulator on the unit is a non-insulated type.



If using a power supply device without an internal protective circuit, always make sure power

is supplied to the unit through a protective element such as a fuse.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание AFP7PSA1














































































































Результаты поиска

Содержание AFP7PSA1

Отзывы:

Похожие инструкции для AFP7PSA1

Бренды по названию

Популярные бренды

Panasonic AFP7PSA1, Руководство пользователя

Результаты поиска

Содержание AFP7PSA1

Отзывы:

Похожие инструкции для AFP7PSA1

Бренды по названию

Популярные бренды