Panasonic AFP7PSA1 Скачать руководство пользователя страница 78

Страница: 78 / 109

8-2

Specifications

8.1 CPU Unit Specifications

8.1.1 General Specifications

Items

Description

Rated voltage

24V DC

Operating voltage range

20.4 to 28.8V DC (Note 1)

Momentary power off time

When the CPU unit only (DC) is used
4 ms (20.4 V is used) , 7 ms (24 V is used) , 10 ms (28.8 V is used)

(Note 2)

Operating ambient
temperature

0 to +55



Storage ambient
temperature

-40 to +70



Operating ambient humidity

10 to 95%RH (at 25



C, no-condensing)

Storage ambient humidity

10 to 95%RH (at 25



C, no-condensing)

Breakdown voltage
(Note 3)

All of the COM port, USB and LAN port
- All of the power supply terminals and functional earths

500V AC,
1 minute

Insulation resistance
(Note 4)

All of the COM port, USB and LAN port
- All of the power supply terminals and functional earths

100 M



larger

Vibration resistance

Based on JIS B 3502 and IEC 61131-2:
5 to 8.4 Hz, half amplitude 3.5 mm
8.4 to 150 Hz, constant acceleration 9.8 m/s

X, Y and Z axes, 10 minutes, 10 sweeps (1 octave/mm)

Shock resistance

Based on JIS B 3502 and IEC 61131-2
147 m/s

, X, Y and Z axes, 3 times

Noise resistance

1,000 V[P-P] with pulse widths 50 ns and 1 µs (using a noise simulator) (power
supply terminals)

Environment

Free from corrosive gases and excessive dust.

EU Directive applicable
standard

EMC Directive: EN 61131-2, Low-Voltage Directive: EN 61131-2

Overvoltage category

Category II or lower

Pollution degree

Pollution degree 2 or lower

(Note 1) When a programmable display GT series is connected to the GT power supply terminal of the CPU unit, use

it within the range of 21.6 to 26.4 V DC.

(Note 2) 10 ms when an AC power supply unit (AFP7PSA1/AFP7PAS2) is used

(Note 3) Cutoff current: 50 mA

(Note 4) With 500 V DC megohmmeter

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание AFP7PSA1














































































































Результаты поиска

Содержание AFP7PSA1

Отзывы:

Похожие инструкции для AFP7PSA1

Бренды по названию

Популярные бренды

Panasonic AFP7PSA1, Руководство пользователя

Результаты поиска

Содержание AFP7PSA1

Отзывы:

Похожие инструкции для AFP7PSA1

Бренды по названию

Популярные бренды