Palazzetti WILMA, Использование и функциональность

Страница: 23 / 68

ENGLISH
VZLWFKHG RII PDQXDOO\ EXWWRQ WKH VWRYH
QHHGV WR EH VWDUWHG GLUHFWO\ IURP WKH FRQWURO
panel.
The stove will go off automatically even in the
case the water temperature keeps growing
notwithstanding the modulation mode. In this case
the stove will ignite only if the difference between
the selected and actual temperature is over 2
ƒ C.
Therefore, if you choose this con ¿ guration, we
suggest that you select a high water temperature
(e.g.. 7
ƒ C).
3.5 OPERATION WITH ROOM PROBE ON
THE BOILER
The boiler can be switched on/off manually or in
programmed mode.
In this type of con
¿ guration, the boiler modulates
output according to the room temperature read
by the probe on the boiler (that is, the boiler
attempts to maintain the desired temperature
while minimising fuel consumption).
,I WKH XVHU KDV HQDEOHG WKH ³(FRPRGH´
IXQFWLRQ XQGHU VXEPHQX
[7]
of the setup
menu
WKH ERLOHU UDWKHU WKDQ PRGXODWLQJ
LWVRXWSXWVZLWFKHVRIIZKHQUHDFKLQJWKHVHW
WHPSHUDWXUHDQGVZLWFKHVRQDJDLQZKHQWKH
URRPWHPSHUDWXUHIDOOVEHORZWKHGHOWDVHWLQ
VXEPHQX
[7]
of the setup menu .
The desired room temperature can be set in
temperature menu
.
6XEPHQX [6]
of the setup menu
can be
used to set the desired water outlet temperature
(the best temperature for the heating system
in question should be suggested by the heating
system installer).
3.6 OPERATION IN COMBINATION WITH A
STORAGE TANK
For operation in combination with a storage tank,
the installer will have set con
¿ guration 3 or 4,
depending on whether the storage tank is with or
without a coil inside.
The boiler is controlled based on the temperature
read by the probe in the storage tank.
When reaching the storage tank temperature set
in the temperature menu
WKHERLOHUVZLWFKHV
RII DQG VZLWFKHV RQ DJDLQ LI WKH WHPSHUDWXUH
IDOOVEHORZWKHGHOWDVHWLQVXEPHQX
[8]
of the
setup menu .
The frost protection function can also be set in this
FRQ¿JXUDWLRQ
3 STOVE OPERATION
3.1 STARTING THE STOVE
Before every ignition, be sure that burning pot is
completely empty and properly positioned in its
seat.
To start the stove hold the
button for several
seconds.
The
À ame icon will start À ashing during the ignition
stage until remaining on steady when the stove has
started.
Automatic stove ignition: the stove comes with an
automatic device that starts the pellet stove without
using other traditional
¿ re lighters.
Avoid lighting the À ame manually if the stove’s
automatic ignition system is not working correctly.
When the stove is started the ¿ rst time, unpleasant
odours or smoke may be generated, caused by
evaporation or drying of certain materials used.
This phenomenon will gradually disappear.
The room should be well ventilated when starting
the stove the
¿ rst few times.
3.2 MODIFYING THE PARAMETERS
The stove operating parameters can be modi ¿ ed
as described.
The values set will be retained until next modi ¿ ed,
even when the stove is switched off or unplugged
from the power supply.
3.3 SWITCHING OFF
To switch the stove off hold the button for a
few seconds; the À ame icon will switch off.
To start the stove again it’s recommended to wait
for the stove to cool down completely.
The stove should only be switched off following the
procedure described above. Never switch the stove
off by unplugging it from the power supply.
3.4 OPERATION WITH ROOM
THERMOSTAT
When the stove is controlled by an external
thermostat (or timer thermostat), the installer must
have set con
¿ guration 1.
In this con ¿ guration the stove switches off when
reaching the external thermostat setting or
alternatively modulates output (that is, the stove
attempts to maintain the desired temperature
while minimising fuel consumption) when reaching
the set water temperature.
The stove switches on again automatically when
the temperature falls below the value set on the
external thermostat (circuit closed).
2Q ILUVW LJQLWLRQ RU LI WKH VWRYH KDV EHHQ
23