ECOFIRE CINDY-CINDY CANALIZZATA-DIAMANTE-AURORA-FENICE-JENNY TURBO
cod. 004770530 - 01/2009
41/102
GB
D
7.3
COMBUSTION START PHASE
7.3.1 Electric power supply
Connect the stove to the electricity mains and press
the switch down, “
I
”, (on) (par 6.3).
If connection is correct, the stove emits an acoustic
signal, the display turns on and the wording
“
PALAZZETTI ECOFIRE
” appears (Fig. 7.2). Two
seconds later “
OFF
” appears, as indicated in Fig. 7.3.1
and on the second line the following parameters
appear in rotation:
POWER;
AIR SPEED;
SET ROOM T.
)
Stove operating parameters can be set in all three
phases.
The adjustment (parameters) are only active in the
working phase. In effect, the “
START
” and “
OFF
” phases
are adjusted automatically. Hence, the
POWER
adjustment in the “
START
” and “
OFF
” phases will define
what the value of the two parameters will be in the
“
WORKING
” phase.
7.3.2 START PHASE (lighting the stove)
To switch-on the stove keep the
ON
key pressed for a
few seconds.
The following message will appear onto the display
“
AWAITING FLAME
”.
This phase is automatic and is completely managed
by the stove. Consequently it is not possible to vary
any parameter (Fig. 7.3.2).
During this phase, the flame is produced and the stove
will reach the operating mode.
The following message will appear onto the display
“
FLAME PRESENT
”.
The stove will automatically move onto the work phase
if the temperature is sufficient to operate correctly
otherwise the NON-START-UP ALARM WILL BE
SIGNALLED (par. 7.7.1).
!
When the stove is new (or when the container is
completely empty) it might not light because the pellet
loading screw needs a few minutes to fill up and
feed the pellets.
To solve this problem simply place a handful of pellets
in the hearth before pressing the
ON
key.
)
Automatic lighting: the stove is equipped with an
automatic device which enables the pellets to be lit
without using other traditional lighters.
7.3
INBETRIEBSETZUNG DER VERBRENNUNG
7.3.1 Stromversorgung
Den Heizofen mit Strom versorgen, indem der
Hauptschalter auf “
I
” gestellt wird (Abs. 6.3).
Bei korrektem Anschluss ertönt ein akustisches
Signal, das Display schaltet sich ein und die Schrift
“
PALAZZETTI ECOFIRE
” (Abb. 7.2) erscheint. Nach 2
Sekunden erscheint die Schrift “
AUS
” laut Abb. 7.3.1
und in der zweiten Zeile erscheinen Laufband folgende
Parameter:
LEISTUNG;
LUFTGESCHW.;
SET RAUM T.
)
Die Betriebsparameter des Heizofens können in
allen drei Phasen eingestellt werden.
Die Einstellungen (Parameter) sind nur während der
Betriebsphase aktiv, denn beim “
START
” und auf “
AUS
”
werden sie automatisch geregelt. Dadurch definiert
die Einstellung der “
LEISTUNG
” während der Phasen
“
START
” und “
AUS
” den Wert der beiden Parameter in
der “
BETRIEBSPHASmE
”.
7.3.2 Phase der INBETRIEBNAHME (Einschalten
des Heizofens)
Zum Anzünden des Heizofens die Taste
ON
einige
Sekunden lang gedrückt halten.
Auf dem Display erscheint die Meldung “
WARTEN AUF
FLAMME
”.
Diese Phase erfolgt automatisch und wird komplett
vom Heizofen gesteuert. Daher kann kein Parameter
geändert werden (Abb. 7.3.2).
Während dieser Phase entsteht die Flamme, und der
Heizofen bringt sich auf Betriebsregime.
Auf dem Display erscheint die Meldung “
FLAMME
VORHANDEN
”.
Ist die Temperatur für einen korrekten Heizofenbetrieb
ausreichend, geht der Heizofen automatisch zur
Betriebsphase über. Andernfalls erscheint die
ALARMMELDUNG FEHLENDE ZÜNDUNG (Abs.
7.7.1).
!
Wenn der Heizofen ganz neu ist (oder der
Brennstoffbehälter komplett entleert wurde), könnte
die Zündung nicht erfolgen, da die
Beschickungsschnecke einige Minuten lang
braucht, um sich anzufüllen und das Feuerbecken
zu versorgen.
Handvoll Pellets ins Feuerbecken legen, bevor die
ON
-Taste gedrückt wird.
)
Automatische Zündung: Der Heizofen ist mit einer
automatischen Vorrichtung ausgestattet, die das
Zünden der Pellets ohne den Gebrauch
herkömmlicher Zündvorrichtungen ermöglicht.